- 您現在的位置：買賣IC網 > PDF目錄384423 > HIP9010AB (INTERSIL CORP) Engine Knock Signal Processor PDF資料下載
參數資料
| 型號： | HIP9010AB |
| 廠商： | INTERSIL CORP |
| 元件分類： | 模擬信號調理 |
| 英文描述： | Engine Knock Signal Processor |
| 中文描述： | SPECIALTY ANALOG CIRCUIT, PDSO20 |
| 封裝： | PLASTIC, MS-013AC, SOIC-20 |
| 文件頁數： | 4/12頁 |
| 文件大小： | 81K |
| 代理商： | HIP9010AB |
4-4
INTEGRATOR
Integrator Offset Voltage
INTGV
IO
By Design
-
0.1
-
mV
Integrator Reset Voltage
V
RESET
Pin 4 Voltage at Initiation of
Integration Cycle. V
DD
= 5V
430
500
570
mV
Integrator Droop after 500
μ
s
V
DROOP
Hold Mode, Pin 7 = 0V, V
DD
= 5V,
Pin 4 set to 20% to 80% of V
DD
-
±
3
±
50
mV
OUTPUT AND SAMPLE AND HOLD
Differential to Single Ended
Converter Offset Voltage
DIFV
IO
By Design
-
0.1
-
mV
Change in Converter Output
DIFOUT
Run Mode, 500
μ
A, Sinking to No Load
-
±
1
±
3
mV
SYSTEM GAIN DEVIATION
Gain Deviation from “Ideal Equation”
Correlation, Factor - 5.0%
V
OUT
-
V
RESET
Run Mode, maximum signal output
from Input Amplifier <2.25V
P-P
,
Equation Output x 0.95 + Device
Reset Voltage. For Total V
OUT
≤
4.7V
-8%,
±
100mV
Equation
x 0.95
-V
RESET
8%,
±
100mV
V
NOTE:
2. Q = f
O
/BW, Where: f
O
= Center Frequency, BW = 3dB bandwidth.
Ideal Equation
When the two filters are set to the same frequency and the input signal is present for the periods T
IN
, then:
R
F
IN
G
R
and G
K
= Programed Gain of Reference and Knock channels.
T
IN
= Time input signal is present In ms.
T
C
= Programmed integrator time constant ms.
N = Number of cycles of input signal.
f
Q
= Frequency of input signal. Assumes both filters are programmed to the same frequency.
V
RESET
= Integrator Reset Voltage.
1.273 = 4/
π
R
F
= Feedback resistor value.
R
IN
= Signal input resistor value.
For example, assume 300mV
P-P
input with the time constant programmed to 300
μ
s and the Integration time is 1.2ms. The R
F
/R
IN
ratio is one and
the Reference channel is programmed to a Gain of 0.188. The Knock channel is then automatically set to a gain of one. The input signal is contin-
uous for the total integration time, T
IN
.
Electrical Specifications
V
DD
= 5V,
±
5%, GND = 0V, Clock Frequency 4MHz,
±
0.5%, T
A
= -40
o
C to 125
o
C,
Unless Otherwise Specified
(Continued)
PARAMETER
SYMBOL
TEST CONDITIONS
MIN
TYP
MAX
UNITS
INTOUT volts
)
Input signal (V
P
P
–
)
R
F
IN
---------
×
G
K
1.273
Q
--------------------------------------------------
×
×
G
R
1.273
Q
--------------------------------------------------
×
×
–
V
RESET
+
=
INTOUT volts
)
Input signal (V
P
P
–
)
---------
×
1.273
T
IN
TC
--------
G
K
G
R
–
(
)
×
V
RESET
+
=
INTOUT volts
)
0.3V (V
P
P
–
)
1.273
-----------------------
1.000
0.188
–
(
)
×
×
×
V
RESET
1.24V
0.500V
1.74V
=
+
=
+
=
HIP9010
相關PDF資料 |
PDF描述 |
|---|---|
| HIP9011ABZ | Engine Knock Signal Processor |
| HIP9011 | Engine Knock Signal Processor |
| HIP9011AB | Engine Knock Signal Processor |
| HIP9020 | Programmable Quad Buffer with Pre and Post Scaler Dividers |
| HIP9020AB | Programmable Quad Buffer with Pre and Post Scaler Dividers |
相關代理商/技術參數 |
參數描述 |
|---|---|
| HIP9011 | 制造商:INTERSIL 制造商全稱:Intersil Corporation 功能描述:Engine Knock Signal Processor |
| HIP9011_06 | 制造商:INTERSIL 制造商全稱:Intersil Corporation 功能描述:Engine Knock Signal Processor |
| HIP9011AB | 功能描述:IC SENSOR ENGINE KNOCK 20-SOIC RoHS:否 類別:集成電路 (IC) >> 接口 - 傳感器和探測器接口 系列:- 其它有關文件:Automotive Product Guide 產品培訓模塊:Lead (SnPb) Finish for COTS Obsolescence Mitigation Program 標準包裝:74 系列:- 類型:觸控式傳感器 輸入類型:數字 輸出類型:數字 接口:JTAG，串行 電流 - 電源:100µA 安裝類型:表面貼裝 封裝/外殼:20-TSSOP（0.173"，4.40mm 寬） 供應商設備封裝:20-TSSOP 包裝:管件 |
| HIP9011ABR4682 | 制造商:Rochester Electronics LLC 功能描述:- Bulk |
| HIP9011ABR4745 | 制造商:Rochester Electronics LLC 功能描述:- Bulk |
發布緊急采購，3分鐘左右您將得到回復。