參數資料
型號: HIP6301VCBZA
廠商: INTERSIL CORP
元件分類: 穩壓器
英文描述: Microprocessor CORE Voltage Regulator Multi-Phase Buck PWM Controller
中文描述: SWITCHING CONTROLLER, 1500 kHz SWITCHING FREQ-MAX, PDSO20
封裝: LEAD FREE, PLASTIC, MS-013AC, SOIC-20
文件頁數: 8/20頁
文件大小: 518K
代理商: HIP6301VCBZA
8
FN9034.2
December 27, 2004
Operation
Figure 1 shows a simplified diagram of the voltage regulation
and current control loops. Both voltage and current feedback
are used to precisely regulate voltage and tightly control the
output currents, I
L1
and I
L2
, of the two power channels. The
voltage loop comprises the error amplifier, comparators, gate
drivers and output MOSFETs. The error amplifier is
essentially connected as a voltage follower that has as an
input, the programmable reference DAC and an output that is
the CORE voltage.
Voltage Loop
Feedback from the CORE voltage is applied via resistor R
IN
to the inverting input of the error amplifier. This signal can
drive the error amplifier output either high or low, depending
upon the CORE voltage. Low CORE voltage makes the
amplifier output move towards a higher output voltage level.
Amplifier output voltage is applied to the positive inputs of
the comparators via the correction summing networks. Out-
of-phase sawtooth signals are applied to the two
Comparators inverting inputs. Increasing error amplifier
voltage results in increased comparator output duty cycle.
This increased duty cycle signal is passed through the PWM
CIRCUIT with no phase reversal and on to the HIP6601B,
again with no phase reversal for gate drive to the upper
MOSFETs, Q1 and Q3. Increased duty cycle or ON time for
the MOSFET transistors results in increased output voltage
to compensate for the low output voltage sensed.
Current Loop
The current control loop works in a similar fashion to the
voltage control loop, but with current control information
applied individually to each channel’s comparator. The
Percent Overvoltage Hysteresis
VSEN Falling after Overvoltage
-
2
-
%
Electrical Specifications
Operating Conditions: V
CC
= 5V, T
A
= 0°C to 70°C, Unless Otherwise Specified
PARAMETER
TEST CONDITIONS
MIN
TYP
MAX
UNITS
CURRENT
SENSING
COMPARATOR
PWM
CIRCUIT
+
RISEN1
+
CORRECTION
ERROR
AMPLIFIER
FB
REFERENCE
ISEN1
RIN
VCORE
Q3
Q4
L02
PHASE
PWM1
IL2
DAC
PROGRAMMABLE
COUT
RLOAD
VIN
HIP6601B
-
Q1
Q2
L01
PHASE
IL1
VIN
HIP6601B
CURRENT
SENSING
COMPARATOR
PWM
CIRCUIT
CORRECTION
PWM2
-
I AVERAGE
+
+
+
-
RISEN2
ISEN2
-
-
-
-
+
+
CURRENT
AVERAGING
FIGURE 1. SIMPLIFIED BLOCK DIAGRAM OF THE HIP6301V VOLTAGE AND CURRENT CONTROL LOOPS FOR
TWO-PHASE REGULATOR
HIP6301V, HIP6302V
相關PDF資料
PDF描述
HIP6301VCBZA-T 150000 SYSTEM GATE 2.5 VOLT FPGA - NOT RECOMMENDED for NEW DESIGN
HIP6301V Microprocessor CORE Voltage Regulator Multi-Phase Buck PWM Controller
HIP6301VCB Microprocessor CORE Voltage Regulator Multi-Phase Buck PWM Controller
HIP6301VCB-T Microprocessor CORE Voltage Regulator Multi-Phase Buck PWM Controller
HIP6301VCBZ Microprocessor CORE Voltage Regulator Multi-Phase Buck PWM Controller
相關代理商/技術參數
參數描述
HIP6301VCBZA-T 制造商:INTERSIL 制造商全稱:Intersil Corporation 功能描述:Microprocessor CORE Voltage Regulator Multi-Phase Buck PWM Controller
HIP6301VCBZ-T 功能描述:電流型 PWM 控制器 MULTI-PHS CNTRLR VID ON THE FLYINTEL VID RoHS:否 制造商:Texas Instruments 開關頻率:27 KHz 上升時間: 下降時間: 工作電源電壓:6 V to 15 V 工作電源電流:1.5 mA 輸出端數量:1 最大工作溫度:+ 105 C 安裝風格:SMD/SMT 封裝 / 箱體:TSSOP-14
HIP6302 制造商:INTERSIL 制造商全稱:Intersil Corporation 功能描述:Microprocessor CORE Voltage Regulator Multi-Phase Buck PWM Controller
HIP6302_04 制造商:INTERSIL 制造商全稱:Intersil Corporation 功能描述:Microprocessor CORE Voltage Regulator Multi-Phase Buck PWM Controller
HIP6302CB 功能描述:IC REG CTRLR BUCK PWM 16-SOIC RoHS:否 類別:集成電路 (IC) >> PMIC - 穩壓器 - DC DC 切換控制器 系列:- 標準包裝:4,000 系列:- PWM 型:電壓模式 輸出數:1 頻率 - 最大:1.5MHz 占空比:66.7% 電源電壓:4.75 V ~ 5.25 V 降壓:是 升壓:無 回掃:無 反相:無 倍增器:無 除法器:無 Cuk:無 隔離:無 工作溫度:-40°C ~ 85°C 封裝/外殼:40-VFQFN 裸露焊盤 包裝:帶卷 (TR)