- 您現在的位置：買賣IC網 > PDF目錄384422 > HIP6200 (Intersil Corporation) Transient Voltage Regulator(瞬變電壓穩壓器) PDF資料下載
參數資料
| 型號： | HIP6200 |
| 廠商： | Intersil Corporation |
| 英文描述： | Transient Voltage Regulator(瞬變電壓穩壓器) |
| 中文描述： | 瞬態電壓調節器（瞬變電壓穩壓器） |
| 文件頁數： | 6/9頁 |
| 文件大小： | 87K |
| 代理商： | HIP6200 |
2-446
Detailed Functional Description
As shown in the Block Diagram, the HIP6200 has two
comparators which compare the voltage on the CAP pin to
the voltage on the SNS pin. The CAP voltage follows the
SNS voltage with an R-C delay which is user programmable
and also variable depending upon the state of the amplifiers.
Normally, resistor R
T1
is in parallel with R
T2
when the
amplifiers are not active. R
T1
is small and the CAP voltage
(V
CAP
) follows the SNS voltage (V
SNS
) closely. During a
transient, when either amplifier is active, the switch in series
with R
T1
opens and R
T2
alone (with the capacitor on CAP)
sets the time constant. Since R
T2
is 20 times larger than
R
T1
, the DeCAPitator has time to source or sink current as
the inductor current slews. The CAP voltage waveform is
depicted in the Typical Application Diagrams.
Prior to the load transient, V
CAP
follows V
OUT
(and
likewise V
SNS
) closely. This is important in many portable
applications because the DC-DC converter will be in an
energy-saving skip-cycle mode at light load currents. In this
mode, the output voltage ripple may be in excess of
±
2%
and could trip the HIP6200’s comparators if V
CAP
did not
track V
SNS
. This would turn on the amplifiers and waste
power. When a fast load transient occurs, V
CAP
no longer
follows V
OUT
and the DeCAPitator becomes active when
V
OUT
exceeds +1% or -1.5% of V
CAP
.
When the DeCAPitator is active, it either supplies current
from the P
VCC
pin or sources current to PGND. Because of
this, a high-quality capacitor must be placed locally from
P
VCC
to GND. The system 5V bus typically has a good
deal of bulk capacitance as well as high frequency
decoupling sprinkled across the application board. P
VCC
is
tied to the system 5V bus through an on-chip 10
resistor.
This resistor helps isolate the system 5V from the
disturbances on P
VCC
.
The HIP6200 has a power-on reset function which ensures
that both V
CC
and CAP are at some minimum levels before
allowing amplifier operation. There is also an EN(ABLE) pin,
allowing users to disable the HIP6200 if desired. An
overtemperature (OT) shutdown feature ensures that the
HIP6200 will not self-destruct from thermal overload. An OT
event will shutdown the chip until the junction temperature
decreases a few degrees below its trip point.
The DeCAPitator draws very little bias current (300
μ
A
typical) when its amplifiers are inactive. When either
amplifier is active, the chip draws 15-30mA of bias current.
This current is mainly for the active high-speed amplifier and
lasts only for the duration of the on-time of the HIP6200.
Component Selection Guidelines
Bulk Output Capacitors
For a given converter design without the HIP6200 in the
target application, the number of output capacitors is
determined mainly by the output voltage regulation and
transient specifications. It is estimated that for a load
transient of 0-8A with a di/dt of 20A/
μ
s, eleven 220
μ
F, 0.1
low ESR tantalum capacitors are necessary to maintain
CPU core voltage regulation specifications. For identical
conditions with a HIP6200 employed, only five 100
μ
F, 0.1
low ESR tantalums are required. Similar savings in output
capacitance can be achieved with other capacitor dielectric-
types.
The number of capacitors which can be eliminated on the
output is limited by either of the following:
1. Output voltage ripple - this increases proportional to the
equivalent ESR of the bulk output capacitance. This may
be counteracted by increasing the output inductance. In
many cases the inductor can remain the same because
the output ripple will still be acceptably small.
2. Leading edge voltage spike - this may increase with re-
duced number of capacitors. The HIP6200 and its very
fast response is very effective in handling this leading
edge spike up to a point. Some additional ceramic decou-
pling on the OUT pin can also help.
P
VCC
Capacitor
A 100
μ
F, 0.1
tantalum is recommended on the P
VCC
pin
for an application which has 8A transients (maximum
recommended operation of the HIP6200). R
VCC
is an
internal 10
resistor from V
CC
to P
VCC
which decouples the
P
VCC
transient from the system 5V (V
CC
).
CAP Capacitor
The capacitor on the CAP pin sets the amount of time that
the HIP6200 has to sink or source current in response to a
load transient. The DeCAPitator on-time should be greater
than the converter response time. When the HIP6200’s
amplifiers are not active, the CAP pin follows the output
voltage closely to prevent false tripping at light loads due to
PWM skip-cycle modes of operation. These two
boundaries are addressed with R
T1
and R
T2
internal to the
HIP6200 but must also be verified on each design.
The converter response time is the time interval required for
the inductor current to slew to the output load current. This
time is dramatically different for the two edges of the
transient event if there is a large differential between input
and output voltages of the converter. The converter
response times are approximated by v = L*di/dt:
where
T
R1
= converter response time to low-to-high load transient
T
R2
= converter response time to high-to-low load transient
T
R1
L
OUT
I
IN
OUT
)
--------------–
=
(EQ. 1)
T
R2
L
OUT
I
OUT
)
--------------------
=
(EQ. 2)
HIP6200, HIP6201
相關PDF資料 |
PDF描述 |
|---|---|
| HIP6201 | Transient Voltage Regulator(瞬變電壓穩壓器) |
| HIP6200CB | Transient Voltage Regulator DeCAPitator⑩ |
| HIP6201CB | Transient Voltage Regulator DeCAPitator⑩ |
| HIP6301CBZ | Microprocessor CORE Voltage Regulator Multi-Phase Buck PWM Controller |
| HIP6301CBZA-T | Microprocessor CORE Voltage Regulator Multi-Phase Buck PWM Controller |
相關代理商/技術參數 |
參數描述 |
|---|---|
| HIP6200CB | 制造商:Rochester Electronics LLC 功能描述:- Bulk |
| HIP6200CB WAF | 制造商:Harris Corporation 功能描述: |
| HIP6200CB-T | 制造商:未知廠家 制造商全稱:未知廠家 功能描述:Transient-Protection Circuit |
| HIP6201 | 制造商:INTERSIL 制造商全稱:Intersil Corporation 功能描述:Transient Voltage Regulator DeCAPitator⑩ |
| HIP6201CB | 制造商:Rochester Electronics LLC 功能描述:- Bulk |
發布緊急采購，3分鐘左右您將得到回復。