- 您現在的位置：買賣IC網 > PDF目錄384422 > HIP6005A (Intersil Corporation) Buck Pulse-Width Modulator (PWM) Controller and Output Voltage Monitor(脈沖帶寬調節控制和輸出電壓檢測電路) PDF資料下載
參數資料
| 型號： | HIP6005A |
| 廠商： | Intersil Corporation |
| 英文描述： | Buck Pulse-Width Modulator (PWM) Controller and Output Voltage Monitor(脈沖帶寬調節控制和輸出電壓檢測電路) |
| 中文描述： | 降壓脈寬調制（PWM）控制器和輸出電壓監視器（脈沖帶寬調節控制和輸出電壓檢測電路） |
| 文件頁數： | 5/12頁 |
| 文件大?。?/td> | 153K |
| 代理商： | HIP6005A |
2-102
Functional Pin Description
V
SEN
(Pin 1)
This pin is connected to the converters output voltage. The
PGOOD and OVP comparator circuits use this signal to
report output voltage status and for overvoltage protection.
OCSET (Pin 2)
Connect a resistor (R
OCSET
) from this pin to the drain of the
upper MOSFET. R
OCSET
, an internal 200
μ
A current source
(I
OCS
), and the upper MOSFET on-resistance (r
DS(ON)
) set
the converter over-current (OC) trip point according to the
following equation:
An over-current trip cycles the soft-start function.
SS (Pin 3)
Connect a capacitor from this pin to ground. This capacitor,
along with an internal 10
μ
A current source, sets the soft-
start interval of the converter.
VID0-4 (Pins 4-8)
VID0-4 are the input pins to the 5-bit DAC. The states of
these five pins program the internal voltage reference
(DACOUT). The level of DACOUT sets the converter output
voltage. It also sets the PGOOD and OVP thresholds. Table
1 specifies DACOUT for the 32 combinations of DAC inputs.
COMP (Pin 9) and FB (Pin 10)
COMP and FB are the available external pins of the error
amplifier. The FB pin is the inverting input of the error
amplifier and the COMP pin is the error amplifier output.
These pins are used to compensate the voltage-control
feedback loop of the converter.
GND (Pin 11)
Signal ground for the IC. All voltage levels are measured with
respect to this pin.
PGOOD (Pin 12)
PGOOD is an open collector output used to indicate the
status of the converter output voltage. This pin is pulled low
when the converter output is not within
±
10% of the
DACOUT reference voltage.
PHASE (Pin 13)
Connect the PHASE pin to the upper MOSFET source. This
pin is used to monitor the voltage drop across the MOSFET
for over-current protection. This pin also provides the return
path for the upper gate drive.
UGATE (Pin 14)
Connect UGATE to the upper MOSFET gate. This pin
provides the gate drive for the upper MOSFET.
BOOT (Pin 15)
This pin provides bias voltage to the upper MOSFET driver.
A bootstrap circuit may be used to create a BOOT voltage
suitable to drive a standard N-Channel MOSFET.
NC (Pin 16)
No connection.
NC (Pin 17)
No connection.
V
CC
(Pin 18)
Provide a 12V bias supply for the chip to this pin.
OVP (Pin 19)
The OVP pin can be used to drive an external SCR in the
event of an overvoltage condition. Output rising 15% more
than the DAC-set voltage triggers a high output on this pin
and disables PWM gate drive circuitry.
RT (Pin 20)
This pin provides oscillator switching frequency adjustment.
By placing a resistor (R
T
) from this pin to GND, the nominal
200kHz switching frequency is increased according to the
following equation:
Conversely, connecting a pull-up resistor (R
T
) from this pin
to V
CC
reduces the switching frequency according to the
following equation:
11
12
13
14
15
16
17
18
20
19
10
9
8
7
6
5
4
3
2
1
V
SEN
OCSET
SS
VID0
VID1
VID2
VID4
VID3
COMP
FB
R
T
OVP
V
CC
NC
NC
BOOT
UGATE
PHASE
PGOOD
GND
I
PEAK
I
-------------------------------------------
R
DS ON
)
=
Fs
200kHz
T
6
)
--------------------
+
≈
(R
T
to GND)
Fs
200kHz
T
7
)
--------------------
–
≈
(R
T
to 12V)
HIP6005A
相關PDF資料 |
PDF描述 |
|---|---|
| HIP6005ACB | Buck Pulse-Width Modulator (PWM) Controller and Output Voltage Monitor |
| HIP6005B | Buck Pulse-Width Modulator (PWM) Controller and Output Voltage Monitor |
| HIP6005BCB | Buck Pulse-Width Modulator (PWM) Controller and Output Voltage Monitor |
| HIP6005BCV | Buck Pulse-Width Modulator (PWM) Controller and Output Voltage Monitor |
| HIP6006CBZ | Buck and Synchronous-Rectifier Pulse-Width Modulator (PWM) Controller |
相關代理商/技術參數 |
參數描述 |
|---|---|
| HIP6005ACB | 制造商:Rochester Electronics LLC 功能描述:- Bulk |
| HIP6005ACB-T | 制造商:Rochester Electronics LLC 功能描述:- Bulk |
| HIP6005B | 制造商:INTERSIL 制造商全稱:Intersil Corporation 功能描述:Buck Pulse-Width Modulator (PWM) Controller and Output Voltage Monitor |
| HIP6005BCB | 制造商:Rochester Electronics LLC 功能描述:PWM CONTROLLER 3.5 TO 1.3V DAC RANGE,20LD SOIC - Bulk |
| HIP6005BCB WAF | 制造商:Harris Corporation 功能描述: |
發布緊急采購，3分鐘左右您將得到回復。