參數資料
型號: HIP6004ECVZ
廠商: INTERSIL CORP
元件分類: 穩壓器
英文描述: Buck and Synchronous-Rectifier (PWM) Controller and Output Voltage Monitor
中文描述: SWITCHING CONTROLLER, 1000 kHz SWITCHING FREQ-MAX, PDSO20
封裝: PLASTIC, TSSOP-20
文件頁數: 7/13頁
文件大?。?/td> 504K
代理商: HIP6004ECVZ
7
Figure 5 shows the critical power components of the converter.
To minimize the voltage overshoot the interconnecting wires
indicated by heavy lines should be part of ground or power
plane in a printed circuit board. The components shown in
Figure 5 should be located as close together as possible.
Please note that the capacitors C
IN
and C
O
each represent
numerous physical capacitors. Locate the HIP6004E within 3
inches of the MOSFETs, Q
1
and Q
2
. The circuit traces for the
MOSFETs’ gate and source connections from the HIP6004E
must be sized to handle up to 1A peak current.
Figure 6 shows the circuit traces that require additional
layout consideration. Use single point and ground plane
construction for the circuits shown. Minimize any leakage
current paths on the SS pin and locate the capacitor, C
SS
close to the SS pin because the internal current source is
only 10
μ
A. Provide local V
CC
decoupling between VCC and
GND pins. Locate the capacitor, C
BOOT
as close as practical
to the BOOT and PHASE pins.
Feedback Compensation
Figure 7 highlights the voltage-mode control loop for a
synchronous-rectified buck converter. The output voltage
(V
OUT
) is regulated to the Reference voltage level. The
error amplifier (Error Amp) output (V
E/A
) is compared with
the oscillator (OSC) triangular wave to provide a pulse-
width modulated (PWM) wave with an amplitude of V
IN
at
the PHASE node.
0
1
0
1
0
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
0
0
1
1
0
0
1
1
1.300
1.325
1.350
1.375
1.400
1.425
0
1
0
1
0
1
0
0
0
0
0
0
1
1
1
1
1
1
1
1
1
1
0
0
1
1
0
0
1
1
1.700
1.725
1.750
1.775
1.800
1.825
NOTE: 0 = connected to GND or V
SS
, 1 = connected to V
DD
through pull-up resistors or leave the pins floating. Internal pull-ups will force the floating
VID pins to HIGH.
TABLE 1. OUTPUT VOLTAGE PROGRAM (Continued)
PIN NAME
NOMINAL OUTPUT
VOLTAGE DACOUT
PIN NAME
NOMINAL OUTPUT
VOLTAGE DACOUT
VID25
mV
VID3
VID2
VID1
VID0
VID25
mV
VID3
VID2
VID1
VID0
PGND
L
O
C
O
LGATE
UGATE
PHASE
Q
1
Q
2
D
2
V
IN
V
OUT
RETURN
HIP6004E
C
IN
L
FIGURE 5. PRINTED CIRCUIT BOARD POWER AND
GROUND PLANES OR ISLANDS
FIGURE 6. PRINTED CIRCUIT BOARD SMALL SIGNAL
LAYOUT GUIDELINES
+12V
HIP6004E
SS
GND
VCC
BOOT
D
1
L
O
C
O
V
OUT
L
Q
1
Q
2
PHASE
+V
IN
C
BOOT
C
VCC
C
SS
HIP6004E
相關PDF資料
PDF描述
HIP6004E Buck and Synchronous-Rectifier (PWM) Controller and Output Voltage Monitor
HIP6004ECB Buck and Synchronous-Rectifier (PWM) Controller and Output Voltage Monitor
HIP6004ECV Buck and Synchronous-Rectifier (PWM) Controller and Output Voltage Monitor
HIP6013 FPGA - 100000 SYSTEM GATE 2.5 VOLT - NOT RECOMMENDED for NEW DESIGN
HIP6013CB FPGA - 100000 SYSTEM GATE 2.5 VOLT - NOT RECOMMENDED for NEW DESIGN
相關代理商/技術參數
參數描述
HIP6004ECVZ-T 功能描述:電壓模式 PWM 控制器 20LD BUCK&SYNCHCT PWMCONOUTPUT RoHS:否 制造商:Texas Instruments 輸出端數量:1 拓?fù)浣Y(jié)構:Buck 輸出電壓:34 V 輸出電流: 開關頻率: 工作電源電壓:4.5 V to 5.5 V 電源電流:600 uA 最大工作溫度:+ 125 C 最小工作溫度:- 40 C 封裝 / 箱體:WSON-8 封裝:Reel
HIP6004EVAL1 功能描述:EVALUATION BOARD HIP6004 RoHS:否 類別:編程器,開發系統 >> 過時/停產零件編號 系列:- 標準包裝:1 系列:- 傳感器類型:CMOS 成像,彩色(RGB) 傳感范圍:WVGA 接口:I²C 靈敏度:60 fps 電源電壓:5.7 V ~ 6.3 V 嵌入式:否 已供物品:成像器板 已用 IC / 零件:KAC-00401 相關產品:4H2099-ND - SENSOR IMAGE WVGA COLOR 48-PQFP4H2094-ND - SENSOR IMAGE WVGA MONO 48-PQFP
HIP6004EVAL3 功能描述:電源管理IC開發工具 EMBEDDED EVAL BRD SYNC BUCK/KLAM RoHS:否 制造商:Maxim Integrated 產品:Evaluation Kits 類型:Battery Management 工具用于評估:MAX17710GB 輸入電壓: 輸出電壓:1.8 V
HIP6005 制造商:INTERSIL 制造商全稱:Intersil Corporation 功能描述:Buck Pulse-Width Modulator (PWM) Controller and Output Voltage Monitor
HIP6005A 制造商:INTERSIL 制造商全稱:Intersil Corporation 功能描述:Buck Pulse-Width Modulator (PWM) Controller and Output Voltage Monitor