- 您現在的位置：買賣IC網 > PDF目錄384421 > HIP4080IB (INTERSIL CORP) 80V/2.5A Peak, High Frequency Full Bridge FET Driver PDF資料下載
參數資料
| 型號： | HIP4080IB |
| 廠商： | INTERSIL CORP |
| 元件分類： | 功率晶體管 |
| 英文描述： | 80V/2.5A Peak, High Frequency Full Bridge FET Driver |
| 中文描述： | 2.6 A FULL BRDG BASED MOSFET DRIVER, PDSO20 |
| 封裝： | PLASTIC, MS-013AC, SOIC-20 |
| 文件頁數： | 13/19頁 |
| 文件大小： | 227K |
| 代理商： | HIP4080IB |
13
HIP4080 Power-up Application Information
The HIP4080 H-Bridge Driver IC requires external circuitry
to assure reliable start-up conditions of the upper drivers. If
not addressed in the application, the H-Bridge power MOS-
FETs may be exposed to shoot-through current, possibly
leading to MOSFET failure. Following the instructions below
will result in reliable start-up.
The HIP4080 does not have an input protocol like the
HIP4081 that keeps both lower power MOSFETs off other
than through the DIS pin. IN+ and IN- are inputs to a com-
parator that control the bridge in such a way that only one of
the lower power devices is on at a time, assuming DIS is low.
However, keeping both lower MOSFETs off can be accom-
plished by controlling the lower turn-on delay pin, LDEL,
while the chip is enabled, as shown in Figure 32. Pulling
LDEL to V
DD
will indefinitely delay the lower turn-on delays
through the input comparator and will keep the lower MOS-
FETs off. With the lower MOSFETs off and the chip enabled,
i.e. DIS = low, IN+ or IN- can be switched through a full
cycle, properly setting the upper driver outputs. Once this is
accomplished, LDEL is released to its normal operating
point. It is critical that IN+/IN- switch a full cycle while LDEL
is held high, to avoid shoot-through. This start-up procedure
can be initiated by the supply voltage and/or the chip enable
command by the circuit in Figure 32.
11
12
13
14
15
16
17
18
20
19
10
9
8
7
6
5
4
3
2
1 BHB
HEN
DIS
V
SS
OUT
IN+
HDEL
IN-
LDEL
AHB
BHO
BLO
BLS
V
DD
V
CC
ALS
BHS
ALO
AHS
AHO
100K
RDEL
RDEL
V
DD
0.1
μ
F
2N3906
V
DD
ENABLE
V
DD
56K
8.2V
56K
100K
FIGURE 32.
V
DD
DIS
LDEL
=10ms
t1
t2
8.3V TO 9.1V (ASSUMING 5% ZENER TOLERANCE)
12V, FINAL VALUE
5.1V
NOTES:
2. Between t1 and t2 the IN+ and IN- inputs must cause the OUT pin to go through one complete cycle (transition order is not important). If
the ENABLE pin is low after the under-voltage circuit is satisfied, the ENABLE pin will initiate the 10ms time delay during which the IN+
and IN- pins must cycle at least once.
3. Another product, HIP4080A, incorporates undervoltage circuitry which eliminates the need for the above power up circuitry.
FIGURE 33. TIMING DIAGRAM FOR FIGURE 32
HIP4080
相關PDF資料 |
PDF描述 |
|---|---|
| HIP4080IP | 80V/2.5A Peak, High Frequency Full Bridge FET Driver |
| HIP4081A | 30000 SYSTEM GATE 3.3 VOLT LOGIC CELL AR - NOT RECOMMENDED for NEW DESIGN |
| HIP4081AIP | 30000 SYSTEM GATE 3.3 VOLT LOGIC CELL AR - NOT RECOMMENDED for NEW DESIGN |
| HIP4081AIB | 80V/2.5A Peak, High Frequency Full Bridge FET Driver |
| HIP4083 | 80V, 300mA Three Phase High Side Driver |
相關代理商/技術參數 |
參數描述 |
|---|---|
| HIP4080IB WAF | 制造商:Harris Corporation 功能描述: |
| HIP4080IB/IP WAF | 制造商:Harris Corporation 功能描述: |
| HIP4080IBR3164 | 制造商:Rochester Electronics LLC 功能描述:- Bulk |
| HIP4080IP | 制造商:Rochester Electronics LLC 功能描述:60-80 VDC, HIGH FREQ H-BRIDGE DRIVER, 20 PDIP - Bulk 制造商:Harris Corporation 功能描述: |
| HIP4080IPR3163 | 制造商:Rochester Electronics LLC 功能描述:- Bulk |
發布緊急采購，3分鐘左右您將得到回復。