- 您現在的位置：買賣IC網 > PDF目錄385380 > HI1-0539-8 (INTERSIL CORP) Precision, 4-Channel, Low-Level, Differential Multiplexer PDF資料下載
參數資料
| 型號： | HI1-0539-8 |
| 廠商： | INTERSIL CORP |
| 元件分類： | 運動控制電子 |
| 英文描述： | Precision, 4-Channel, Low-Level, Differential Multiplexer |
| 中文描述： | 4-CHANNEL, DIFFERENTIAL MULTIPLEXER, CDIP16 |
| 封裝： | CERDIP-16 |
| 文件頁數： | 8/11頁 |
| 文件大?。?/td> | 189K |
| 代理商： | HI1-0539-8 |
8
Application Information
General
The Hl-539 accepts inputs in the range -15V to +15V, with
performance guaranteed over the
±
10V range. At these
higher levels of analog input voltage it is comparable to the Hl-
509, and is plug-in compatible with that device (as well as the
Hl-509A). However, as mentioned earlier, the Hl-539 was
designed to introduce minimum error when switching low level
inputs.
Special care is required in working with these low level
signals. The main concern with signals below 100mV is that
noise, offset voltage, and other aberrations can represent a
large percentage error. A shielded differential signal path is
essential to maintain a noise level below 50
μ
V
RMS
.
Low Level Signal Transmission
The transmission cable carrying the transducer signal is critical
in a low level system. It should be as short as practical and
rigidly supported. Signal conductors should be tightly twisted
for minimum enclosed area to guard against pickup of
electromagnetic interference, and the twisted pair should be
shielded against capacitively coupled (electrostatic)
interference. A braided wire shield may be satisfactory, but a
lapped foil shield is better since it allows only
1
/
10
as much
leakage capacitance to ground per foot. A key requirement for
the transmission cable is that it presents a balanced line to
sources of noise interference. This means an equal series
impedance in each conductor plus an equally distributed
impedance from each conductor to ground. The result should
be signals equal in magnitude but opposite in phase at any
transverse plane. Noise will be coupled in phase to both
conductors, and may be rejected as common-mode voltage by
a differential amplifier connected to the multiplexer output.
Coaxial cable is not suitable for low level signals because the
two conductors (center and shield) are unbalanced. Also,
ground loops are produced if the shield is grounded at both
ends by standard BNC connectors. If coax must be used, carry
the signal on the center conductors of two equal-length cables
whose shields are terminated only at the transducer end. As a
general rule, terminate (ground) the shield at one end only,
preferably at the end with greatest noise interference. This is
usually the transducer end for both high and low level signals.
Watch Small
V Errors
Printed circuit traces and short lengths of wire can add
substantial error to a signal even after it has traveled
hundreds of feet and arrived on a circuit board. Here, the
small voltage drops due to current flow through connections
of a few milliohms must be considered, especially to meet an
accuracy requirement of 12 bits or more.
Table 1 is a useful collection of data for calculating the effect
of these short connections. (Proximity to a ground plane will
lower the values of inductance.)
As an example, suppose the Hl-539 is feeding a 12-bit
converter system with an allowable error of
±
1
/
2
LSB
(
±
1.22mV). lf the interface logic draws 100mA from the 5V
supply, this current will produce 1.28mV across 6 inches of
#24 wire; more than the error budget. Obviously, this digital
current must not be routed through any portion of the analog
ground return network.
FIGURE 7A. SINGLE-ENDED CROSSTALK TEST CIRCUIT
FIGURE 7B. DIFFERENTIAL CROSSTALK TEST CIRCUIT
FIGURE 7. CROSSTALK
Test Circuits and Waveforms
Unless Otherwise Specified T
A
= 25
o
C, V+ = +15V, V- = -15V, V
AH
= 4V and V
AL
= 0.8V
(Continued)
HI-539
INSTRUMENTATION
AMPLIFIER
AD606 or BB3630, for Example
+
-
G = 1000
350
1kHz,
15V
P-P
AD606 or BB3630, for example
HI-539
INSTRUMENTATION
AMPLIFIER
+
-
G = 1000
350
1kHz,
15V
P-P
350
HI-539
相關PDF資料 |
PDF描述 |
|---|---|
| HI-539 | Precision, 4-Channel, Low-Level, Differential Multiplexer |
| HI3-0546-5 | Single 16 and 8, Differential 8-Channel and 4-Channel CMOS Analog MUXs with Active Overvoltage Protection |
| HI9P0546-9 | Single 16 and 8, Differential 8-Channel and 4-Channel CMOS Analog MUXs with Active Overvoltage Protection |
| HI9P0547-9 | Power Resistor; Series:200; Resistance:900ohm; Resistance Tolerance: 5%; Power Rating:8W; Resistor Element Material:Ceramic; Temperature Coefficient:260 ppm; Leaded Process Compatible:No; Packaging:Bulk RoHS Compliant: No |
| HI9P0548-5 | Single 16 and 8, Differential 8-Channel and 4-Channel CMOS Analog MUXs with Active Overvoltage Protection |
相關代理商/技術參數 |
參數描述 |
|---|---|
| HI1-0539B | 制造商:Rochester Electronics LLC 功能描述:- Bulk |
| HI1-0544-2 | 制造商:Harris Corporation 功能描述: |
| HI1-0546/883 | 制造商:Intersil Corporation 功能描述:MUX 16:1 OVP 28CDIP /883 - Rail/Tube |
| HI1-0546/883S2356 | 制造商:Rochester Electronics LLC 功能描述:- Bulk |
| HI1-0546-2 | 功能描述:多路器開關 IC MUX 16:1 OVP 28CDIP MIL RoHS:否 制造商:Texas Instruments 通道數量:1 開關數量:4 開啟電阻（最大值）:7 Ohms 開啟時間（最大值）: 關閉時間（最大值）: 傳播延遲時間:0.25 ns 工作電源電壓:2.3 V to 3.6 V 工作電源電流: 最大工作溫度:+ 85 C 安裝風格:SMD/SMT 封裝 / 箱體:UQFN-16 |
發布緊急采購，3分鐘左右您將得到回復。