- 您現在的位置：買賣IC網 > PDF目錄370575 > HFCT-5305 Gigabit Ethernet: 1.25 GBd 1300 nm Laser Transceiver in Low Cost 1 x 9 Package Style PDF資料下載
參數資料
| 型號： | HFCT-5305 |
| 英文描述： | Gigabit Ethernet: 1.25 GBd 1300 nm Laser Transceiver in Low Cost 1 x 9 Package Style |
| 中文描述： | 千兆位以太網：1.25 GBd 1300 nm激光收發器的低成本1 × 9封裝形式 |
| 文件頁數： | 6/8頁 |
| 文件大?。?/td> | 178K |
| 代理商： | HFCT-5305 |
570
Table 1. Pinout Table
Pin
Symbol
Mounting Studs
Functional Description
The mounting studs are provided for transceiver mechanical attachment to the circuit
board, they are embedded in the nonconductive plastic housing and are not tied to the
transceiver internal circuit. They should be soldered into plated-through holes on the
printed circuit board.
Receiver Signal Ground
Directly connect this pin to receiver signal ground plane.
Receiver Data Out
See recommended circuit schematic.
Receiver Data Out Bar
See recommended circuit schematic.
Signal Detect
Normal optical input levels to the receiver result in a logic “1” output.
Low optical input levels to the receiver result in a fault condition indication shown by
a logic “0” output.
Signal Detect is a single-ended, low-power, PECL output. Since SD is a low-power
PECL output, complete the interconnection of SD output with other PECL inputs using
a 10 k
pull-down resistor to V
EE
to allow biasing of this interconnection. Do not load
this SD output with standard PECL, 50
to V
CC
– 2 V, termination. If Signal Detect
output is not used, leave it open-circuited.
This Signal Detect output can be used to drive a PECL input on an upstream circuit,
such as, Signal Detect input or Loss of Signal-bar.
Receiver Power Supply
Provide +5 V dc via the recommended transmitter power supply filter circuit.
Locate the power supply filter circuit as close as possible to the V
CCR
pin.
Transmitter Power Supply
Provide +5 V dc via the recommended transmitter power supply filter circuit.
Locate the power supply filter circuit as close as possible to the V
CCT
pin.
Transmitter Data In Bar
See recommended circuit schematic.
Transmitter Data In
See recommended circuit schematic.
Transmitter Signal Ground
Directly connect this pin to the transmitter signal ground plane.
1
V
EER
2
RD+
3
RD–
4
SD
5
V
CCR
6
V
CCT
7
TD–
8
TD+
9
V
EET
Figure 1. Pinout.
1
2
3
4
5
6
7
8
9
TOP VIEW
N/C
N/C
RECEIVER SIGNAL GROUND
RECEIVER DATA OUT
RECEIVER DATA OUT BAR
SIGNAL DETECT
RECEIVER POWER SUPPLY
TRANSMITTER POWER SUPPLY
TRANSMITTER DATA IN BAR
TRANSMITTER DATA IN
TRANSMITTER SIGNAL GROUND
相關PDF資料 |
PDF描述 |
|---|---|
| HFCT-53D3 | 1 x 9 Fiber Optic Transceivers for Fibre Channel(光通道的1 x 9光纖收發器) |
| HFCT-53D5 | 1 x 9 Fiber Optic Transceivers for Gigabit Ethernet(千兆位以太網應用的1 x 9光纖收發器) |
| HFCT-5402D | 2488 Mb/s Single Mode Fiber Transceiver for SONET OC-48/SDH STM-16 and ATM(應用于SONET OC-48/SDH STM-16 和ATM的2488 Mb/s 單模式光收發器) |
| HFCT-5903E | MT-RJ Duplex Single Mode Transceiver(MT-RJ 雙工單模式收發器) |
| HFCT-5905E | MT-RJ Duplex Single Mode Transceiver(MT-RJ 雙工單模式收發器) |
相關代理商/技術參數 |
參數描述 |
|---|---|
| HFCT53D3 | 制造商:未知廠家 制造商全稱:未知廠家 功能描述:FIBER OPTIC TRANSCEIVER |
| HFCT53D3EM | 制造商:未知廠家 制造商全稱:未知廠家 功能描述:FIBER OPTIC TRANSCEIVER |
| HFCT-53D3EM | 制造商:未知廠家 制造商全稱:未知廠家 功能描述:1 x 9 5V Fiber Optic Transceiver for Fibre Channel/Storage - Extended Shield. Metalized Housing |
| HFCT53D3FM | 制造商:未知廠家 制造商全稱:未知廠家 功能描述:FIBER OPTIC TRANSCEIVER |
| HFCT-53D3FM | 制造商:未知廠家 制造商全稱:未知廠家 功能描述:1 x 9 5V Fiber Optic Transceiver for Fibre Channel/Storage - Flush Shield. Metalized Housing |
發布緊急采購，3分鐘左右您將得到回復。