參數資料
型號： HFBR-4663
英文描述： Single Chip 10BASE-FL Transceiver(單芯片10BASE-FL收發器)
中文描述： 單片上10BASE -佛羅里達州收發器（單芯片的10 Base -佛羅里達州收發器）
文件頁數： 9/16頁
文件大?。?/td> 211K
代理商： HFBR-4663
9
correct RTSET resistor:
RTSET= 52 mA
l62
IOUT
(
)
The transmitter enters the idle
state when it detects start of idle
on Tx+ and Tx- input pins. After
detecting the start of idle, the
transmitter switches to a 1 MHz
output idle signal.
The output current is switched
through the TxOUT pin during the
on cycle and the V
CC
Tx pin during
the off cycle as shown in figure 2.
Since the sum of the current in
these two pins is constant, V
CC
Tx
should be connected as close as
possible to the V
CC
connection for
the LED.
If not driving an optical LED
directly, a differential output can
be generated by tying resistors
from V
CC
Tx and TxOUT to V
CC
as
shown in Figure 3. The minimum
voltage on these two pins should
not be less than V
CC
- 2 V.
Figure 3. Converting Optical LED Driver Output to Differential ECL.
Loopback
The loopback function emulates a
10BASE-T transceiver whereby
the transmit data sent by the DTE
is looped back over the AUI
receive pair. Some LAN
controllers use this loopback
information to determine whether
a MAU is connected by
monitoring the carrier sense while
transmitting. The software can
use this loopback information to
determine whether a MAU is
connected to the DTE by
checking the status of carrier
sense after each packet
transmission.
When data is received by the chip
while transmitting, a collision
condition exits. This will cause
the collision oscillator to turn on
and the data on the DI pair will
follow V
IN
+, V
IN
-. After a collision
is detected, the collision oscillator
will remain on until either DO or
V
IN
+, V
IN
- go idle.
Loopback can be disabled by
strapping LBDIS to V
CC
. In this
mode the chip operates as a full
duplex transmitter and receiver,
and collision detection is disabled.
A loopback through the
transceiver can be accomplished
by tying the fiber transmitter to
the receiver.
Reception
The input to the transceiver
comes from a fiber optic receiver
as shown in figure 1. At the start
of packet reception no more than
2.7 bits are received from the
fiber cable and not transmitted
onto the DI circuit. The receive
squelch will reject frequencies
lower than 2.51 MHz.
While in the unsquelch state, the
receive squelch circuit looks for
the start of idle signal at the end
of the packet. Start of idle occurs
when the input signal remains idle
for more than 160 ns. When start
of idle is detected, the receive
squelch circuit returns to the
squelch state and the start of idle
signal is output on the DI circuit
(Rx+, Rx-).
Collision
Whenever the receiver and the
transmitter are active at the same
time the chip will activate the
collision output, except when
loopback is disabled (LBDIS =
Vcc). The collision output is a
differential square wave matching
the AUI specifications and
capable of driving a 78
load.
The frequency of the square wave
is 10 MHz
±
15% with a 60/40 to
40/60 duty cycle. The collision
oscillator also is activated during
SQE Test and jabber.
Figure 2. Fiber Optic LED Driver
Structure.
V
CC
Tx
TxOUT
I
OUT
V
CC
Tx
TxOUT
V
CC
51
51
51
ECL
RTSET = 560
I
OUT
= 15.9 mA
相關PDF資料
PDF描述
HFBR-5103 1300 nm 2000 m，F(xiàn)DDI, 100 Mbps ATM, and Fast Ethernet Transceivers in Low Cost 1x9 Package Style(1300 nm 2000 m，F(xiàn)DDI, 100 Mbps ATM, 快速以太網收發器（低價格 1x9 封裝類型）)
HFBR-5103T 1300 nm 2000 m，F(xiàn)DDI, 100 Mbps ATM, and Fast Ethernet Transceivers in Low Cost 1x9 Package Style(1300 nm 2000 m，F(xiàn)DDI, 100 Mbps ATM, 快速以太網收發器（低價格 1x9 封裝類型）)
HFBR-5104T 800 nm 500 m，F(xiàn)DDI, 100 Mbps ATM, and Fast Ethernet Transceivers in Low Cost 1x9 Package Style(800 nm 500 m，F(xiàn)DDI, 100 Mbps ATM, 快速以太網收發器（低價格 1x9 封裝類型）)
HFBR-5105T 1300nm 500 m，F(xiàn)DDI, 100 Mbps ATM, and Fast Ethernet Transceivers in Low Cost 1x9 Package Style(1300nm 500 m，F(xiàn)DDI, 100 Mbps ATM, 快速以太網收發器（低價格 1x9 封裝類型）)
HFBR-5104 800 nm 500 m，F(xiàn)DDI, 100 Mbps ATM, and Fast Ethernet Transceivers in Low Cost 1x9 Package Style(800 nm 500 m，F(xiàn)DDI, 100 Mbps ATM, 快速以太網收發器（低價格 1x9 封裝類型）)
相關代理商/技術參數
參數描述
HFBR-5000 功能描述:SC DUPLEX 1X9 PORT PLUG RoHS:否 類別:光電元件 >> 配件 系列:- 標準包裝:1 系列:- 附件類型:USB 纜線 適用于相關產品:GTT-480270A 其它名稱:635-1047
HFBR-5001 功能描述:光纖連接器 Port Plug for FDDI M IC Transceivers RoHS:否 制造商:Molex 產品:Adapters 類型:8 Port with External Shutter 連接器類型:Adapter 模式:Multimode 光纖直徑: 顏色:Blue 附件類型:LC Adapter
HFBR-5002 制造商:Avago Technologies 功能描述:DUST COVER - Bulk
HFBR-5003 功能描述:SFF MT-RJ PORT PLUG RoHS:是 類別:光電元件 >> 配件 系列:- 標準包裝:1 系列:- 附件類型:USB 纜線 適用于相關產品:GTT-480270A 其它名稱:635-1047
HFBR-5004 制造商:Avago Technologies 功能描述:EDL VINYL PORT CAPS - Bulk
發布緊急采購，3分鐘左右您將得到回復。

采購需求

(若只采購一條型號，填寫一行即可)

發布成功！您可以繼續發布采購。也可以進入我的后臺，查看報價

發布成功！您可以繼續發布采購。也可以進入我的后臺，查看報價

*型號 *數量 廠商 批號 封裝
添加更多采購

我的聯系方式

*
*
*