- 您現在的位置：買賣IC網 > PDF目錄94823 > HFBR-4535 SIMPLEX FIBER OPTIC CONNECTOR PDF資料下載
參數資料
| 型號： | HFBR-4535 |
| 元件分類： | 光纖連接器 |
| 英文描述： | SIMPLEX FIBER OPTIC CONNECTOR |
| 文件頁數： | 2/5頁 |
| 文件大?。?/td> | 226K |
| 代理商： | HFBR-4535 |
2
Step 2: Putting on the Connector
Place the connector on each end of the fiber, and slide
the connector down until the fiber jacket stops it. The
fiber should protrude no less than 1.5 mm (0.06 in) from
the end of the connector.
To install simplex connectors flip the top half of the con-
nector over and snap it into the ferrule half (with your
fingers). When the top half latches inside the body of
the ferrule half, proper connector-to-cable attachment
is achieved.
For duplex connector installation place one connector
on top of the other, so that the top half of each connec-
tor is over the ferrule half of the opposite connector.
Manually press connectors together in the center of
the arrangement. Then latch by pressing on the sides
of each connector. As with the simplex version, connec-
tors are secured when top halves latch into the ferrule
halves.
Termination Guide
Step-by-Step Plastic Cable Connectoring Instructions
The following step-by-step guide describes how to
terminate plastic fiber optic cable. It is ideal for both
field and factory installations. Connectors can be easily
installed on cable ends with standard tools such as wire
strippers and cutters.
Finishing the cable is accomplished with the Avago
Technologies HFBR-4593 Polishing Kit, consisting of a
polishing fixture, 600 grid abrasive paper and 3 mm
pink lapping film (3M Company, OC3-14). The connec-
tor can be used immediately after polishing.
The following materials are needed for plastic fiber ter-
mination:
1. Plastic optical fiber cable (Example: HFBR-RUD500)
2. Wire cutters or scissors
3. 16 gauge wire stripper (Example: Ideal Stripmaster
type 45-092)
4. HFBR-4593 polishing kit (optional)
5. Crimpless connectors
Step 1: Stripping the Fiber
The zip cord structure of the duplex cable permits easy
separation of the channels. The channels should be
separated a minimum of 100 mm (4 in) to a maximum
of 150 mm (6 in) back from the ends to permit connec-
toring, polishing and cable end flexibility.
After cutting the cable to the desired length, strip off
approximately 7 mm (0.3 in) of the outer jacket with the
16 gauge wire strippers.
When using the duplex connector arrangement, the
separated duplex cable should be stripped to roughly
equal lengths on each cable end.
For the non-latching version (HFBR-4531), the same
connector is used for simplex and duplex arrangement.
No crimping is necessary. The top half of the connector
will snap into the ferrule half to secure the fiber.
相關PDF資料 |
PDF描述 |
|---|---|
| HFW27R-2STE1MTLF | 27 CONTACT(S), FEMALE, RIGHT ANGLE FFC/FPC CONNECTOR, SURFACE MOUNT |
| HFW28R-2STE1MTLF | 28 CONTACT(S), FEMALE, RIGHT ANGLE FFC/FPC CONNECTOR, SURFACE MOUNT |
| HFW29R-2STE1MTLF | 29 CONTACT(S), FEMALE, RIGHT ANGLE FFC/FPC CONNECTOR, SURFACE MOUNT |
| HFW30R-2STE1MTLF | 30 CONTACT(S), FEMALE, RIGHT ANGLE FFC/FPC CONNECTOR, SURFACE MOUNT |
| HFW4R-2STE1MTLF | 4 CONTACT(S), FEMALE, RIGHT ANGLE FFC/FPC CONNECTOR, SURFACE MOUNT |
相關代理商/技術參數 |
參數描述 |
|---|---|
| HFBR-4535Z | 功能描述:光纖連接器 Snap-In FO Connector Crimpless RoHS:否 制造商:Molex 產品:Adapters 類型:8 Port with External Shutter 連接器類型:Adapter 模式:Multimode 光纖直徑: 顏色:Blue 附件類型:LC Adapter |
| HFBR-4593 | 功能描述:光纖連接器 VERS LINK DUPLEX Polishing Kit RoHS:否 制造商:Molex 產品:Adapters 類型:8 Port with External Shutter 連接器類型:Adapter 模式:Multimode 光纖直徑: 顏色:Blue 附件類型:LC Adapter |
| HFBR-4593Z | 功能描述:光纖連接器 VERS LINK DUPLEX Polishing Kit RoHS:否 制造商:Molex 產品:Adapters 類型:8 Port with External Shutter 連接器類型:Adapter 模式:Multimode 光纖直徑: 顏色:Blue 附件類型:LC Adapter |
| HFBR4597 | 制造商:Avago Technologies 功能描述:CRIMP TOOL FIBRE OPTIC 制造商:Avago Technologies 功能描述:CRIMP TOOL, FIBRE OPTIC |
| HFBR-4597 | 功能描述:折皺器 Crimp Tool p POF RoHS:否 制造商:Hirose Connector 類型: 描述/功能:Cable and Shield Crimper |
發(fā)布緊急采購，3分鐘左右您將得到回復。