- 您現在的位置：買賣IC網 > PDF目錄361282 > HFBR-0537 Eval Kit for proprietary data com apps at data rates up to 32 MBd with AN 1121 figs. 3 & 5 PDF資料下載
參數資料
| 型號： | HFBR-0537 |
| 英文描述： | Eval Kit for proprietary data com apps at data rates up to 32 MBd with AN 1121 figs. 3 & 5 |
| 中文描述： | 評估套件與安1121無花果專有數據的COM應用程序的數據傳輸速率高達32萬桶。 3 |
| 文件頁數： | 6/11頁 |
| 文件大小： | 267K |
| 代理商： | HFBR-0537 |
6
Step 3
Any excess fiber protruding from
the connector end may be cut off;
however, the trimmed fiber
should extend at least 1.5 mm
(0.06 in) from the connector end.
Insert the connector fully into the
polishing fixture with the trimmed
fiber protruding from the bottom
of the fixture. This plastic polish-
ing fixture can be used to polish
two simplex connectors or simplex
latching connectors simultane-
ously, or one duplex connector.
Note:
The four dots on the
bottom of the polishing fixture
are wear indicators. Replace
the polishing fixture when any
dot is no longer visible.
Typically, the polishing fixture
can be used 10 times; 10 duplex
connectors or 20 simplex
connectors, two at a time.
Place the 600 grit abrasive paper
on a flat smooth surface, pressing
down on the connector, polish the
fiber and the connector using a
figure eight pattern of strokes
until the connector is flush with
the bottom of the polishing
fixture. Wipe the connector and
fixture with a clean cloth or
tissue.
Step 4
Place the flush connector and
polishing fixture on the dull side
of the 3
μ
m pink lapping film and
continue to polish the fiber and
connector for approximately 25
strokes. The fiber end should be
flat, smooth and clean.
This cable is now ready for use.
Note:
Use of the pink lapping
film fine polishing step results
in approximately 2 dB
improvement in coupling
performance of either a
transmitter-receiver link or a
bulkhead/splice over a 600 grit
polish alone. This fine polish is
comparable to the Agilent
factory polish. The fine
polishing step may be omitted
where an extra 2 dB of optical
power is not essential, as with
short link lengths. Proper
polishing of the tip of the fiber/
connector face results in a tip
diameter between 2.5 mm
(0.098 in.) minimum and 3.2
mm (0.126 in.) maximum..
HFBR-4593 Polishing Kit
相關PDF資料 |
PDF描述 |
|---|---|
| HFBR-1521 | 5 MBd 600nm High Performance Link Transmitter in Horizontal Package |
| HFBR-1523 | 40 kBd 600nm Low Current/Extended Distance Link Transmitter in Horizontal Package |
| HFBR-1524 | 1 MBd 600nm Standard Link Transmitter in Horizontal Package |
| HFBR-1531 | 5 MBd 600nm High Performance Link Transmitter in Vertical Package |
| HFBR-1532 | 1 MBd 600nm High Performance Link Transmitter in Vertical Package |
相關代理商/技術參數 |
參數描述 |
|---|---|
| HFBR-0537Z | 制造商:Avago Technologies 功能描述:32MBD 650NM SIMPLE TTL EVAL KIT |
| HFBR-0538 | 功能描述:光學纖維開發工具 500kb and 2MBd Evaluation Kit RoHS:否 制造商:Omron Electronics 產品:Evaluation Boards 用于:SX51 封裝: |
| HFBR-0538Z | 功能描述:光學纖維開發工具 DC-2MBd Inrbus 650nm Evaluation Kit RoHS:否 制造商:Omron Electronics 產品:Evaluation Boards 用于:SX51 封裝: |
| HFBR-0539 | 功能描述:光學纖維開發工具 Profibus up to 12MBd Evaluation Kit RoHS:否 制造商:Omron Electronics 產品:Evaluation Boards 用于:SX51 封裝: |
| HFBR-0539Z | 功能描述:光學纖維開發工具 DC-12MBd PFbus 650nm Evaluation Kit RoHS:否 制造商:Omron Electronics 產品:Evaluation Boards 用于:SX51 封裝: |
發布緊急采購，3分鐘左右您將得到回復。