- 您現在的位置：買賣IC網 > PDF目錄361282 > HFBR-0527H Evaluation Kit for HFBR-1527 & HFBR-2526 125MBd Data Comm HCS Fiber for up to 100 meters PDF資料下載
參數資料
| 型號： | HFBR-0527H |
| 英文描述： | Evaluation Kit for HFBR-1527 & HFBR-2526 125MBd Data Comm HCS Fiber for up to 100 meters |
| 中文描述： | 評估板的HFBR - 1527 |
| 文件頁數： | 6/11頁 |
| 文件大?。?/td> | 267K |
| 代理商： | HFBR-0527H |
6
Step 3
Any excess fiber protruding from
the connector end may be cut off;
however, the trimmed fiber
should extend at least 1.5 mm
(0.06 in) from the connector end.
Insert the connector fully into the
polishing fixture with the trimmed
fiber protruding from the bottom
of the fixture. This plastic polish-
ing fixture can be used to polish
two simplex connectors or simplex
latching connectors simultane-
ously, or one duplex connector.
Note:
The four dots on the
bottom of the polishing fixture
are wear indicators. Replace
the polishing fixture when any
dot is no longer visible.
Typically, the polishing fixture
can be used 10 times; 10 duplex
connectors or 20 simplex
connectors, two at a time.
Place the 600 grit abrasive paper
on a flat smooth surface, pressing
down on the connector, polish the
fiber and the connector using a
figure eight pattern of strokes
until the connector is flush with
the bottom of the polishing
fixture. Wipe the connector and
fixture with a clean cloth or
tissue.
Step 4
Place the flush connector and
polishing fixture on the dull side
of the 3
μ
m pink lapping film and
continue to polish the fiber and
connector for approximately 25
strokes. The fiber end should be
flat, smooth and clean.
This cable is now ready for use.
Note:
Use of the pink lapping
film fine polishing step results
in approximately 2 dB
improvement in coupling
performance of either a
transmitter-receiver link or a
bulkhead/splice over a 600 grit
polish alone. This fine polish is
comparable to the Agilent
factory polish. The fine
polishing step may be omitted
where an extra 2 dB of optical
power is not essential, as with
short link lengths. Proper
polishing of the tip of the fiber/
connector face results in a tip
diameter between 2.5 mm
(0.098 in.) minimum and 3.2
mm (0.126 in.) maximum..
HFBR-4593 Polishing Kit
相關PDF資料 |
PDF描述 |
|---|---|
| HFBR-0527P | Evaluation Kit for HFBR-1527 & HFBR-2526 125MBd Data Comm with POF for up to 25 meters |
| HFBR-0537 | Eval Kit for proprietary data com apps at data rates up to 32 MBd with AN 1121 figs. 3 & 5 |
| HFBR-1521 | 5 MBd 600nm High Performance Link Transmitter in Horizontal Package |
| HFBR-1523 | 40 kBd 600nm Low Current/Extended Distance Link Transmitter in Horizontal Package |
| HFBR-1524 | 1 MBd 600nm Standard Link Transmitter in Horizontal Package |
相關代理商/技術參數 |
參數描述 |
|---|---|
| HFBR-0527HZ | 功能描述:光學纖維開發工具 125MBd 650nm HCS Evaluation Kit RoHS:否 制造商:Omron Electronics 產品:Evaluation Boards 用于:SX51 封裝: |
| HFBR-0527P | 功能描述:光學纖維開發工具 125MBd Data Comm POF Evaluation Kit RoHS:否 制造商:Omron Electronics 產品:Evaluation Boards 用于:SX51 封裝: |
| HFBR-0527PZ | 功能描述:光學纖維開發工具 125MBd 650nm POF Evaluation Kit RoHS:否 制造商:Omron Electronics 產品:Evaluation Boards 用于:SX51 封裝: |
| HFBR-0528 | 功能描述:光學纖維開發工具 10 MBd Txcvr Evaluation Kit RoHS:否 制造商:Omron Electronics 產品:Evaluation Boards 用于:SX51 封裝: |
| HFBR-0528Z | 功能描述:光學纖維開發工具 DC-10MBd 650nm POF Evaluation Kit RoHS:否 制造商:Omron Electronics 產品:Evaluation Boards 用于:SX51 封裝: |
發布緊急采購，3分鐘左右您將得到回復。