參數資料
型號： HD66727A03TA0L
廠商： Hitachi,Ltd.
英文描述： Low-Power Dot-Matrix Liquid Crystal Display Controller/Driver with Key Scan Function
中文描述： 低功耗點陣液晶顯示控制器/鍵掃描功能驅動程序
文件頁數： 86/97頁
文件大小： 513K
代理商： HD66727A03TA0L
HD66727
86
Standby Mode
Setting the standby mode bit (STB) to 1 puts the HD66727 in the standby mode, where the device stops
completely, halting all internal operations including the R-C oscillator, thus further reducing current
consumption compared to that in the sleep mode. Specifically, character and segment displays, which are
controlled by the multiplexing drive method, are completely halted. Here, all the SEG (SEG1 to SEG60)
and COM (COM1 to COM34) pins output the V
CC
level, resulting in no display. If the AMP bit is set to 0
in the standby mode, the LCD drive power supply can be turned off.
Annunciators can be displayed simply by supplying an approximately 40-Hz alternating signal for the LCD
drive signals to the EXM pin externally. If annunciator display is unnecessary during the standby mode, the
EXM pin must be fixed to the V
CC
or GND level and the annunciator display on bit (DA) set to 0.
During the standby mode, no instructions can be accepted other than those for annunciator display, the
start-oscillator instruction, and the key scan interrupt generation enable instruction. To cancel the standby
mode, issue the start oscillator instruction to stabilize R-C oscillation before setting the STB bit to 0.
Although key scan is halted in the standby mode, the HD66727 can detect four key inputs connected with
strobe signal KST0, thus generating the key scan interrupt (IRQ*). This means, the system can be activated
from the completely inactive state. For details, refer to the Key Scan Control section.
Figure 50 shows the procedure for setting and canceling the standby mode.
Turn off the LCD power supply: AMP = 0
Only for annunciator display;
set the DA bit to 0 when
annunciator display is not necessary.
Set standby mode: STB = 1
Supply an external alternating signal to the EXM pin
Issue the start-oscillator instruction
Wait at least 10 ms
Cancel standby mode: STB = 0
Turn on the LCD drive power supply: AMP = 1
Standby mode (only annunciator display is available)
Figure 50 Procedure for Setting and Canceling Standby Mode
相關PDF資料
PDF描述
HD66705U Low-Power Dot-Matrix Liquid Crystal Display Controller/Driver(圖形LCD控制器/驅動器)
HD66710 (Dot Matrix Liquid Crystal Display Controller/Driver)
HD66710A00FS 16 AMP SPDT MINIATURE POWER RELAY
HD66710A00TF (Dot Matrix Liquid Crystal Display Controller/Driver)
HD66712U Dot-Matrix Liquid Crystal Display Controller/Driver(點陣液晶顯示控制器/驅動器)
相關代理商/技術參數
參數描述
HD66727A04 制造商:未知廠家 制造商全稱:未知廠家 功能描述:LCD Display Driver
HD66727A04BP 制造商:未知廠家 制造商全稱:未知廠家 功能描述:LCD Display Driver
HD66727A04TA0 制造商:未知廠家 制造商全稱:未知廠家 功能描述:LCD Display Driver
HD66727A04TA0L 制造商:HITACHI 制造商全稱:Hitachi Semiconductor 功能描述:Low-Power Dot-Matrix Liquid Crystal Display Controller/Driver with Key Scan Function
HD66728 制造商:HITACHI 制造商全稱:Hitachi Semiconductor 功能描述:128 x 128-dot Graphics LCD Controller/Driver with Four-grayscale Functions
發布緊急采購，3分鐘左右您將得到回復。

采購需求

(若只采購一條型號，填寫一行即可)

發布成功！您可以繼續發布采購。也可以進入我的后臺，查看報價

發布成功！您可以繼續發布采購。也可以進入我的后臺，查看報價

*型號 *數量 廠商 批號 封裝
添加更多采購

我的聯系方式

*
*
*