亚洲av香蕉一区二区三区,人人操夜夜操

您現在的位置：買賣IC網 > PDF目錄370459 > HD4074394S (Hitachi,Ltd.) 4-bit HMCS400-series microcomputer(4位單片微計算機) PDF資料下載

參數資料

型號：	HD4074394S
廠商：	Hitachi,Ltd.
英文描述：	4-bit HMCS400-series microcomputer(4位單片微計算機)
中文描述：	4位HMCS400系列微電腦（4位單片微計算機）
文件頁數：	25/100頁
文件大?。?/td>	610K
代理商：	HD4074394S

HD404344R Series/HD404394 Series

Interrupts

There are five kinds of interrupts: external

INT

, timer B, timer C, serial interface, and A/D converter.

An interrupt request flag or an interrupt mask and vector address are used for each type of interrupt. They

are used for storing interrupt requests and interrupt controls. An interrupt enable flag is also used for total

interrupt control.

Interrupt Control Bits and Interrupt Processing:

The interrupt control bits are mapped from $000 to

$003 of RAM and can be accessed by RAM bit manipulation instructions. However, the interrupt request

flag (IF) cannot be set by software. An MCU reset initializes the interrupt enable flag (IE) and the interrupt

request flag (IF) to 0, and the interrupt mask (IM) to 1.

A block diagram of the interrupt control circuit is shown in figure 8. The interrupt priority order and vector

addresses are listed in a table in the figure, along with the conditions for executing the interrupt processing

of the five types of interrupt requests (table 2). An interrupt request occurs when the interrupt request flag

is set to 1 and the interrupt mask to 0. If the interrupt enable flag is 1, interrupt processing has occurred.

The vector address which corresponds to the interrupt source is generated from the priority PLA.

The interrupt processing sequence is shown in figure 9 and the interrupt processing flowchart is shown in

figure 10. After receiving an interrupt, the previous instruction is completed in the first cycle. The interrupt

enable flag (IE) is reset after two cycles. The contents of the carry flag, status flag, and program counter are

stored onto the stack at the second and third cycles. Instruction execution is restarted by jumping to the

vector address during the third cycle. The JMPL instructions, which branch to the start addresses of the

interrupt routines, should be programmed at each vector address area. The interrupt request which initiated

the interrupt processing should be reset by software instructions in the interrupt routine.

相關PDF資料	PDF描述
HD40C4341R	4-bit HMCS400-series microcomputer(4位單片微計算機)
HD40C4342R	4-bit HMCS400-series microcomputer(4位單片微計算機)
HD40C4344R	4-bit HMCS400-series microcomputer(4位單片微計算機)
HD404342R	4-bit HMCS400-series microcomputer(4位單片微計算機)
HD404344R	4-bit HMCS400-series microcomputer(4位單片微計算機)

相關代理商/技術參數	參數描述
HD4074408C	制造商:未知廠家制造商全稱:未知廠家功能描述:4-Bit Microcontroller
HD4074408F	制造商:未知廠家制造商全稱:未知廠家功能描述:4-Bit Microcontroller
HD4074408H	制造商:未知廠家制造商全稱:未知廠家功能描述:4-Bit Microcontroller
HD4074408S	制造商:Renesas Electronics Corporation 功能描述:HIT 4 BIT MICROCOMPUTER (ZTAT)
HD4074418C	制造商:未知廠家制造商全稱:未知廠家功能描述:4-Bit Microcontroller

發布緊急采購，3分鐘左右您將得到回復。

(若只采購一條型號，填寫一行即可)

*型號	*數量	廠商	批號	封裝

添加更多采購