參數資料
型號： HD4048212R
廠商： Hitachi,Ltd.
英文描述： AS Microcomputer Incorporating a LCD controller/Driver Circuit(帶LCD控制/驅動電路的微計算機)
中文描述： 由于微機安裝有LCD控制器/驅動電路（帶液晶控制/驅動電路的微計算機）
文件頁數： 34/147頁
文件大?。?/td> 519K
代理商： HD4048212R
HD404829R Series
34
Stop Mode:
In stop mode, all MCU operations stop and RAM data is retained. Therefore, the power
dissipation in this mode is the least of all modes. The OSC
1
and OSC
2
oscillator stops. For the X1 and X2
oscillator to operate or stop can be selected by setting bit 3 of the system clock select register (SSR: $029;
operating: SSR3 = 0, stop: SSR3 = 1) (figure 27). The MCU enters stop mode if the STOP instruction is
executed in active mode when bit 3 of timer mode register A (TMA: $008) is set to 0 (TMA3 = 0) (figure
44).
Stop mode is terminated by a RESET input or a
STOPC
input as shown in figure 16. RESET or
STOPC
must be applied for at least one t
RC
to stabilize oscillation (refer to the AC Characteristics section). When
the MCU restarts after stop mode is cancelled, all RAM contents before entering stop mode are retained,
but the accuracy of the contents of the accumulator, B register, W register, X/SPX register, Y/SPY register,
carry flag, and serial data register cannot be guaranteed.
Stop mode
Oscillator
Internal
clock
STOP instruction execution
(at least equal to oscillator stabilization time t
RC
)
t
res
RESET
STOPC
Figure 16 Timing of Stop Mode Cancellation
Watch Mode:
In watch mode, the clock function (timer A) using the X1 and X2 oscillator and the LCD
function operate, but other function operations stop. Therefore, the power dissipation in this mode is the
second least to stop mode, and this mode is convenient when only clock display is used. In this mode, the
OSC
1
and OSC
2
oscillator stops, but the X1 and X2 oscillator operates. The MCU enters watch mode if
the STOP instruction is executed in active mode when TMA3 = 1, or if the STOP or SBY instruction is
executed in subactive mode.
Watch mode is terminated by a RESET input or a timer-A/
INT
0
interrupt request. For details of RESET
input, refer to the Stop Mode section. When terminated by a timer-A/
INT
0
interrupt request, the MCU
enters active mode if LSON = 0, or subactive mode if LSON = 1. After an interrupt request is generated,
the time required to enter active mode is t
RC
for a timer A interrupt, and T
X
(where T + t
RC
< T
X
< 2T +
t
RC
) for an
INT
0
interrupt, as shown in figures 17 and 18.
Operation during mode transition is the same as that at standby mode cancellation (figure 15).
相關PDF資料
PDF描述
HD4074829 AS Microcomputer Incorporating a LCD controller/Driver Circuit(帶LCD控制/驅動電路的微計算機)
HD404828R AS Microcomputer Incorporating a LCD controller/Driver Circuit(帶LCD控制/驅動電路的微計算機)
HD404829R AS Microcomputer Incorporating a LCD controller/Driver Circuit(帶LCD控制/驅動電路的微計算機)
HD4048412 4-Bit Single-Chip Microcomputer
HD4048412FS 4-Bit Single-Chip Microcomputer
相關代理商/技術參數
參數描述
HD4048212RFS 制造商:RENESAS 制造商全稱:Renesas Technology Corp 功能描述:AS Microcomputer Incorporating a LCD controller/Driver Circuit
HD4048212RH 制造商:RENESAS 制造商全稱:Renesas Technology Corp 功能描述:AS Microcomputer Incorporating a LCD controller/Driver Circuit
HD4048212RTF 制造商:RENESAS 制造商全稱:Renesas Technology Corp 功能描述:AS Microcomputer Incorporating a LCD controller/Driver Circuit
HD4048212TF 制造商:未知廠家 制造商全稱:未知廠家 功能描述:4-Bit Microcontroller
HD404828FS 制造商:未知廠家 制造商全稱:未知廠家 功能描述:4-Bit Microcontroller
發布緊急采購，3分鐘左右您將得到回復。

采購需求

(若只采購一條型號，填寫一行即可)

發布成功！您可以繼續發布采購。也可以進入我的后臺，查看報價

發布成功！您可以繼續發布采購。也可以進入我的后臺，查看報價

*型號 *數量 廠商 批號 封裝
添加更多采購

我的聯系方式

*
*
*