- 您現在的位置：買賣IC網 > PDF目錄367056 > HD-3900M3-BH (Hirose Electric USA, INC.) 3 dB 90∑ Card Couplers PDF資料下載
參數資料
| 型號： | HD-3900M3-BH |
| 廠商： | Hirose Electric USA, INC. |
| 英文描述： | 3 dB 90∑ Card Couplers |
| 中文描述： | 3分貝90Σ卡耦合器 |
| 文件頁數： | 8/9頁 |
| 文件大?。?/td> | 584K |
| 代理商： | HD-3900M3-BH |
34
I
Mounting Method
Figure 1.
Figure 3.
Figure 4.
Fastening screw
Microstrip board
Micro stripline
Tab
Figure 2.
The three types of mounting methods
illustrated in the diagrams below will
mount the card coupler for use under
optimum conditions.
The fastening screws in the diagrams
are M2 screws tightened to 1.5 kg
cm.
When the tip of the micro stripline is of
Teflon type material ( r = 2.6), C
chamfering of C1 is performed at t1.6,
and of C0.5 at t1.2.
The side view diagrams of Figure 1 are
illustrated in Figures 2, 3, and 4 below.
Gap S between the card coupler and
the microstrip board surface should be
used to agree with the following
conditions.
Below 500 MHz........S
≤
0.5 mm
500 to 2300 MHz......S
≤
0.25 mm
Above 2300 MHz......S
≤
0.15 mm
Metal plate or conductive spacer
G
When the Ground Board is Constructed of 0.4 mm Stainless and 0.8 mm Aluminum
(When the Thickness of the Microstrip Board is 1.6 or 1.2 mm)
For t1.6 boards, use with the stainless case of the card coupler facing upward. For t1.2 boards,
use with the aluminum case of the card coupler facing upward. Mount and fix the card coupler
with fastening screws as illustrated in Figure 2. Next, solder the tabs and micro stripline, then
use.
(When the Thickness of the Microstrip Board is Greater than 1.6 mm)
Insert a metal plate or a conductive spacer between the coupler and ground, then mount as
illustrated in Figure 3 so that the surface of the tabs and the position of the microstrip board are
equal. Fix the card coupler with fastening screws as illustrated in Figure 3. Next, solder the tabs
and micro stripline, then use.
(When the Thickness of the Microstrip Board is Less than 1.2 mm)
Cut the ground at the position of the coupler and attach so that the surface of the tabs is in
contact with the micro stripline. Fix the card coupler with fastening screws as illustrated in Figure
4. Next, solder the tabs and micro stripline, then use.
∏
相關PDF資料 |
PDF描述 |
|---|---|
| HD-02103AST | SCR Thyristor; Thyristor Type:Sensitive Gate; Peak Repetitive Off-State Voltage, Vdrm:60V; On-State RMS Current, IT(rms):800mA; Peak Non Repetitive Surge Current, Itsm:8A; Gate Trigger Current Max, Igt:200uA |
| HD1530FX | High Voltage NPN Power Transistor for High Definition and New Super-Slim CRT Display |
| HDA-CTF1 | CTF SERIES PLASTIC D SUBMINIATURE SHELL(ACCESSORIES) |
| HDC-CTF | IC,Audio Amplifier,SINGLE,DIP,14PIN,PLASTIC RoHS Compliant: Yes |
| HDE-CTF | IC-DUAL OP AMP-8 PIN DIP |
相關代理商/技術參數 |
參數描述 |
|---|---|
| HD3A | 制造商:未知廠家 制造商全稱:未知廠家 功能描述:SOT 23 SILICON PLANAR HIGH SPEED SWITCHING DIODES |
| HD3A-4D | 制造商:未知廠家 制造商全稱:未知廠家 功能描述:SOT 23 SILICON PLANAR HIGH SPEED SWITCHING DIODES |
| HD3ATA | 功能描述:二極管 - 通用，功率，開關 - RoHS:否 制造商:STMicroelectronics 產品:Switching Diodes 峰值反向電壓:600 V 正向連續電流:200 A 最大浪涌電流:800 A 配置: 恢復時間:2000 ns 正向電壓下降:1.25 V 最大反向漏泄電流:300 uA 最大功率耗散: 工作溫度范圍: 安裝風格:SMD/SMT 封裝 / 箱體:ISOTOP 封裝:Tube |
| HD3ATC | 功能描述:二極管 - 通用，功率，開關 - RoHS:否 制造商:STMicroelectronics 產品:Switching Diodes 峰值反向電壓:600 V 正向連續電流:200 A 最大浪涌電流:800 A 配置: 恢復時間:2000 ns 正向電壓下降:1.25 V 最大反向漏泄電流:300 uA 最大功率耗散: 工作溫度范圍: 安裝風格:SMD/SMT 封裝 / 箱體:ISOTOP 封裝:Tube |
| HD3LMS32E | 制造商:Energizer Battery Company 功能描述:MICRO SPORT HEADLIGHTENERGIZER INDUSTRIAL 制造商:Energizer Battery Company 功能描述:ENR MICRO SPORT HEADLIGHT 制造商:Energizer Battery Company 功能描述:MICRO SPORT HEADLIGHT ENERGIZER INDUSTRIAL |
發布緊急采購，3分鐘左右您將得到回復。