參數資料
型號: HCPL7840
元件分類: 運動控制電子
英文描述: Analog Isolation Amplifier
中文描述: 模擬隔離放大器
文件頁數: 1/12頁
文件大?。?/td> 217K
代理商: HCPL7840
1-248
H
CAUTION: It is advised that normal static precautions be taken in handling and assembly of this component to
prevent damage and/or degradation which may be induced by ESD.
HCPL-7840
Analog Isolation Amplifier
Technical Data
A 0.1 F bypass capacitor must be connected between pins 1 and 4 and between pins 5 and 8.
Features
High Common Mode
Rejection (CMR): 15 kV/
μ
s
at V
CM
= 1000 V
5% Gain Tolerance
0.1% Nonlinearity
Low Offset Voltage and Off-
set Temperature Coefficient
100 kHz Bandwidth
Performance Specified Over
-40
°
C to 85
°
C Temperature
Range
Recognized Under UL 1577
and CSA Approved for
Dielectric Withstand Proof
Test Voltage of 2500 Vac, 1
Minute
Standard 8-Pin DIP Package
Applications
Motor Phase and Rail
Current Sensing
Inverter Current Sensing
Switched Mode Power
Supply Signal Isolation
General Purpose Current
Sensing and Monitoring
General Purpose Analog
Signal Isolation
Description
The HCPL-7840 isolation ampli-
fier provides accurate, electrically
isolated and amplified representa-
tions of voltage and current.
When used with a shunt resistor
in the current path, the HCPL-
7840 offers superior reliability,
cost effectiveness, size and
autoinsertability compared with
the traditional solutions such as
current transformers and Hall-
effect sensors.
The HCPL-7840 consists of a
sigma-delta analog-to-digital
converter optically coupled to a
digital-to-analog converter.
Superior performance in design
critical specifications such as
common-mode rejection, offset
voltage, nonlinearity, operating
temperature range and regulatory
compliance make the HCPL-7840
the clear choice for designing
reliable, lower-cost, reduced-size
products such as motor
controllers and inverters.
Common-mode rejection of
15 kV/
μ
s makes the HCPL-7840
suitable for noisy electrical
environments such as those
generated by the high switching
rates of power IGBTs.
Low offset voltage together with
a low offset voltage temperature
coefficient permits accurate use
of auto-calibration techniques.
Gain tolerance of 5% with 0.1%
nonlinearity further provide the
performance necessary for
accurate feedback and control.
A wide operating temperature
range with specified performance
allows the HCPL-7840 to be used
in hostile industrial environments.
Functional Diagram
1
2
3
4
8
7
6
5
I
DD1
V
DD1
V
IN+
V
IN–
GND1
I
DD2
V
DD2
V
OUT+
V
OUT–
GND2
+
+
SHIELD
5965-4784E
相關PDF資料
PDF描述
HCS00HMSR CAP CERM .22UF 10% 50V X7R 0805
HCS00D Radiation Hardened Quad 2-Input NAND Gate
HCS00DMSR RES 1.65K-OHM 1% 0.10W 100PPM THK-FILM SMD-0603 TR-7-PA ROHS
HCS00K Radiation Hardened Quad 2-Input NAND Gate
HCS00KMSR Radiation Hardened Quad 2-Input NAND Gate
相關代理商/技術參數
參數描述
HCPL-7840 功能描述:隔離放大器 4.5 - 5.5 SV 8 dB RoHS:否 制造商:Texas Instruments 輸入補償電壓:1.5 mV 共模抑制比(最小值):95 dB 帶寬:60 KHz 工作電源電壓:3.3 V 電源電流:8 mA 工作溫度范圍:- 40 C to + 105 C 安裝風格:SMD/SMT 封裝 / 箱體:SOP-8 封裝:Tube
HCPL-7840#060 功能描述:隔離放大器 4.5 - 5.5 SV 8 dB RoHS:否 制造商:Texas Instruments 輸入補償電壓:1.5 mV 共模抑制比(最小值):95 dB 帶寬:60 KHz 工作電源電壓:3.3 V 電源電流:8 mA 工作溫度范圍:- 40 C to + 105 C 安裝風格:SMD/SMT 封裝 / 箱體:SOP-8 封裝:Tube
HCPL-7840#300 功能描述:隔離放大器 4.5 - 5.5 SV 8 dB RoHS:否 制造商:Texas Instruments 輸入補償電壓:1.5 mV 共模抑制比(最小值):95 dB 帶寬:60 KHz 工作電源電壓:3.3 V 電源電流:8 mA 工作溫度范圍:- 40 C to + 105 C 安裝風格:SMD/SMT 封裝 / 箱體:SOP-8 封裝:Tube
HCPL-7840#360 功能描述:隔離放大器 4.5 - 5.5 SV 8 dB RoHS:否 制造商:Texas Instruments 輸入補償電壓:1.5 mV 共模抑制比(最小值):95 dB 帶寬:60 KHz 工作電源電壓:3.3 V 電源電流:8 mA 工作溫度范圍:- 40 C to + 105 C 安裝風格:SMD/SMT 封裝 / 箱體:SOP-8 封裝:Tube
HCPL-7840#500 功能描述:隔離放大器 4.5 - 5.5 SV 8 dB RoHS:否 制造商:Texas Instruments 輸入補償電壓:1.5 mV 共模抑制比(最小值):95 dB 帶寬:60 KHz 工作電源電壓:3.3 V 電源電流:8 mA 工作溫度范圍:- 40 C to + 105 C 安裝風格:SMD/SMT 封裝 / 箱體:SOP-8 封裝:Tube