- 您現在的位置：買賣IC網 > PDF目錄384393 > HC5517IB (HARRIS SEMICONDUCTOR) GIGATRUE 550 CAT PATCH CBL NO BOOT 6FT RD 25 PK PDF資料下載
參數資料
| 型號： | HC5517IB |
| 廠商： | HARRIS SEMICONDUCTOR |
| 元件分類： | 模擬傳輸電路 |
| 英文描述： | GIGATRUE 550 CAT PATCH CBL NO BOOT 6FT RD 25 PK |
| 中文描述： | TELECOM-SLIC, PDSO28 |
| 文件頁數： | 15/18頁 |
| 文件大?。?/td> | 175K |
| 代理商： | HC5517IB |
74
Additional Tip and Ring Offset Voltage
A DC offset is required to level shift tip and ring from ground
and V
BAT
respectively. By design, the tip amplifier is offset
4V below ground and the ring amplifier is offset 4V above
V
BAT
. The 4V offset was designed so that the peak voice
signal could pass through the SLIC without distortion. There-
fore, to maintain distortion free transmission of pulse meter-
ing and voice, an additional offset equal to the peak of the
pulse metering signal is required.
The tip and ring voltages are offset by a voltage divider
network on the V
RX
pin. The V
RX
pin is a unity gain input
designed as the 4-wire side voice input for the SLIC.
Figure 13 details the circuit used to generate the additional
offset voltage.
The amplifier shown is the tip amplifier. Other signals are con-
nected to the summing node of the amplifier but only those
components used for the offset generation are shown. The off-
set generated at the output of the tip amplifier is summed at the
ring amplifier inverting input to provide a positive offset from the
battery voltage. The connection to the ring amplifier was omit-
ted from Figure 13 for clarity, refer to Figure 3 for details.
The term V
PMO
is defined to be the offset required for the
pulse metering signal. The value of the offset voltage is cal-
culated as the peak value of the pulse metering signal.
Equation 45 assumes the amplitude of the pulse metering
signal is expressed as an RMS voltage.
The value of R
6
can be calculated from the following
equation:
The component labeled R is the internal summing resistor of
the tip amplifier and has a typical value of 108k
. The value
of R
7
should be selected in the range of 4.99k
and 10k
.
Staying within these limits will minimize the parallel loading
effects of the internal resistor R on R
7
as well as minimize
the constant power dissipation introduced by the divider.
Solving Equation 45 for 1V
RMS
results in a 1.414V
requirement for V
PMO
. Setting R
7
of Equation 46 to 10k
and substituting the values for V
PMO
and R yields 23.2k
for
R
6
. The value of R
6
can be rounded to the nearest standard
value without significantly changing the offset voltage.
Single Low Voltage Supply Operation
The application circuit shown Figure 15 requires 2 low
voltage supplies (+5V, -5V). The following application offers
away to make use of a 2.5V reference, provided with some
CODEC, to operate the transhybrid balance amplifier from
a single +5V supply. The implementation is shown in
Figure 14. Notice that the three inputs from the SLIC must all
be AC coupled to insure the proper DC gain through the
CODECs internal op amp. The resistor Ra is not used for
gain setting and is only intended to balance the DC offsets
generated by the input bias current of the CODEC amplifier.
If the DC offsets generated by the input bias currents are
negligible, then Ra may be omitted from the circuit. Ca may
be required for decoupling of the voltage reference pin and
does not contribute to the response of the amplifier.
Layout Guidelines and Considerations
The printed circuit board trace length to all high impedance
nodes should be kept as short as possible. Minimizing length
will reduce the risk of noise or other unwanted signal pickup.
The short lead length also applies to all high gain inputs. The
set of circuit nodes that can be categorized as such are:
V
RX
pin 27, the 4-wire voice input.
-IN1 pin 13, the inverting input of the internal amplifier.
V
REF
pin 3, the noninverting input to ring feed amplifier.
V
RING
pin 24, the 20V/V input for the ringing signal
U1 pin 2, inverting input of external amplifier.
For multi layer boards, the traces connected to tip should not
cross the traces connected to ring. Since they will be carrying
high voltages, and could be subject to lightning or surge
depending on the application, using a larger than minimum
trace width is advised.
The 4-wire transmit and receive signal paths should not
cross. The receive path is any trace associated with the V
RX
input and the transmit path is any trace associated with V
TX
output. The physical distance between the two signal paths
should be maximized to reduce crosstalk.
The mode control signals and detector outputs should be
routed away from the analog circuitry. Though the digital
signals are nearly static, care should be taken to minimize
coupling of the sharp digital edges to the analog signals.
2-WIRE SIDE
R
R
R
6
R
7
C
7
C
5
TO VOICE INPUT OF
TRANSHYBRID AMP
+5V
4-WIRE SIDE
VOICE INPUT
V
PMO
FIGURE 13. PULSE METERING OFFSET GENERATION
+
-
V
RX
V
PMO
2
V
PM
=
(EQ. 45)
R
6
R
R
7
R
+
-----------------
5
V
PMO
–
-------------------------
=
(EQ. 46)
V
PM
R
2
R
3
R
1
OUT
1
V
RX
R
4
CODEC
Ra
Ca
0.1
μ
F
24.9k
0.1
μ
F
0.1
μ
F
0.1
μ
F
24.9k
FIGURE 14. SINGLE LOW VOLTAGE SUPPLY OPERATION
2.4V
REF
+
-
HC5517
相關PDF資料 |
PDF描述 |
|---|---|
| HC55180 | Extended Reach Ringing SLIC Family |
| HC55181 | Extended Reach Ringing SLIC Family |
| HC55182 | Extended Reach Ringing SLIC Family |
| HC55183 | Extended Reach Ringing SLIC Family |
| HC55184 | Extended Reach Ringing SLIC Family |
相關代理商/技術參數 |
參數描述 |
|---|---|
| HC5517IM | 制造商:Rochester Electronics LLC 功能描述:- Bulk |
| HC5517IM96 | 制造商:Rochester Electronics LLC 功能描述:- Bulk |
| HC55180 | 制造商:INTERSIL 制造商全稱:Intersil Corporation 功能描述:Extended Reach Ringing SLIC Family |
| HC55180_05 | 制造商:INTERSIL 制造商全稱:Intersil Corporation 功能描述:Extended Reach Ringing SLIC Family |
| HC55180CIM | 制造商:Rochester Electronics LLC 功能描述:- Bulk |
發(fā)布緊急采購，3分鐘左右您將得到回復。