- 您現在的位置：買賣IC網 > PDF目錄370423 > HAL300 (Electronic Theatre Controls, Inc.) Differential Hall Effect Sensor IC PDF資料下載
參數資料
| 型號： | HAL300 |
| 廠商： | Electronic Theatre Controls, Inc. |
| 英文描述： | Differential Hall Effect Sensor IC |
| 中文描述： | 差分霍爾效應傳感器IC |
| 文件頁數： | 11/13頁 |
| 文件大?。?/td> | 143K |
| 代理商： | HAL300 |
HAL320
11
Micronas
Application Notes
Mechanical stress can change the sensitivity of the Hall
plates and an offset of the magnetic switching points
may result. External mechanical stress on the sensor
must be avoided if the sensor is used under back-biased
conditions. This piezo sensitivity of the sensor IC cannot
be completely compensated for by the switching offset
compensation technique.
In order to assure switching the sensor on and off in a
back-biased application, the minimum magnetic modu-
lation of the differential field should amount to more than
10% of the magnetic preinduction.
If the HAL320 sensor IC is used in back-biased applica-
tions, please contact our Application Department. They
will provide assistance in avoiding applications which
may induce stress to the ICs. This stress may cause
drifts of the magnetic parameters indicated in this data
sheet.
For electromagnetic immunity, it is recommended to ap-
ply a 4.7 nF capacitor between V
DD
(pin 1) and Ground
(pin 2). For automotive applications, a 220 series re-
sistor to pin 1 is recommended. Because of the I
DD
peak
at 3.5 V, the series resistor should not be greater than
270
. The series resistor and the capacitor should be
placed as close as possible to the IC. For optimal EMC
behavior, the test circuits in Fig. 21 and Fig. 22 are rec-
ommended.
Ambient Temperature
Due to the internal power dissipation, the temperature
on the silicon chip (junction temperature T
J
) is higher
than the temperature outside the package (ambient tem-
perature T
A
).
T
J
= T
A
+
T
At static conditions, the following equations are valid:
T = I
DD
* V
DD
* R
thJSB
–
for TO-92UA:
T = I
DD
* V
DD
* R
thJA
–
for SOT-89x:
For typical values, use the typical parameters. For worst
case calculation, use the max. parameters for I
DD
and
R
th
, and the max. value for V
DD
from the application.
Recommended Test Circuits
for Electromagnetic Compatibility
Test pulses V
EMC
corresponding to DIN 40839.
OUT
GND
3
2
1
V
DD
4.7 nF
V
EMC
V
P
R
V
220
R
L
1.2 k
20 pF
Fig. 21:
Test circuit 2: test procedure for class A
OUT
GND
3
2
1
V
DD
4.7 nF
V
EMC
R
V
220
R
L
680
Fig. 22:
Test circuit 1: test procedure for class C
相關PDF資料 |
PDF描述 |
|---|---|
| HAL320 | Differential Hall Effect Sensor IC |
| HAL509 | Hall Effect Sensor Family |
| HAL502A | Hall Effect Sensor Family |
| HAL502E | 400 POS B2B® FEMALE CONNECTOR W/3M |
| HAL502K | 400 POS B2B® FEMALE CONNECTOR W/TR |
相關代理商/技術參數 |
參數描述 |
|---|---|
| HAL300_1 | 制造商:MICRONAS 制造商全稱:MICRONAS 功能描述:Differential Hall Effect Sensor IC |
| HAL300S | 制造商:未知廠家 制造商全稱:未知廠家 功能描述:Analog IC |
| HAL300-S | 制造商:LEM 制造商全稱:LEM 功能描述:Current Transducer HAL 50~600-S |
| HAL300SF-A | 制造商:MICRONAS 制造商全稱:MICRONAS 功能描述:Differential Hall Effect Sensor IC |
| HAL300SF-K | 制造商:MICRONAS 制造商全稱:MICRONAS 功能描述:Differential Hall Effect Sensor IC |
發布緊急采購，3分鐘左右您將得到回復。