- 您現在的位置：買賣IC網 > PDF目錄10839 > HA3-5020-5 (Intersil)IC OPAMP VIDEO CFA 100MHZ 8-DIP PDF資料下載
參數資料
| 型號： | HA3-5020-5 |
| 廠商： | Intersil |
| 文件頁數： | 21/23頁 |
| 文件大小： | 0K |
| 描述： | IC OPAMP VIDEO CFA 100MHZ 8-DIP |
| 標準包裝： | 50 |
| 應用： | 電流反饋 |
| 電路數： | 1 |
| -3db帶寬： | 100MHz |
| 轉換速率： | 1100 V/µs |
| 電流 - 電源： | 7.5mA |
| 電流 - 輸出 / 通道： | 31.7mA |
| 電壓 - 電源，單路/雙路(±)： | ±4.5 V ~ 18 V |
| 安裝類型： | 通孔 |
| 封裝/外殼： | 8-DIP（0.300"，7.62mm） |
| 供應商設備封裝： | 8-PDIP |
| 包裝： | 管件 |
7
FN2845.12
May 21, 2013
-3dB Bandwidth (Note 17)
VOUT = 100mV
25
-
65
-
MHz
Settling Time to 1%
2V Output Step
25
-
75
-
ns
Settling Time to 0.25%
2V Output Step
25
-
130
-
ns
INTERSIL VALUE ADDED SPECIFICATIONS
Input Noise Voltage (Note 17)
f = 1kHz
25
-
4.5
-
nV/
√Hz
+Input Noise Current (Note 17)
f = 1kHz
25
-
2.5
-
pA/
√Hz
-Input Noise Current (Note 17)
f = 1kHz
25
-
25
-
pA/
√Hz
Input Common Mode Range
Full
±2.5V
-V
Output Current, Short Circuit
VIN = ±2.5V, VOUT = 0V
Full
±40
±60
-
mA
Output Current, Disabled (Note 17)
DISABLE = 0V,
VOUT = ±2.5V, VIN = 0V
Full
-
2
A
Output Disable Time (Notes 17, 23)
25
-
40
-
s
Output Enable Time (Notes 17, 21)
25
-
40
-
ns
Supply Voltage Range
25
±5
-
±15
V
Output Capacitance, Disabled (Note 22)
DISABLE = 0V
25
-
6
-
pF
VIDEO CHARACTERISTICS
Differential Gain (Notes 16, 17)
RL = 150Ω
25
-
0.03
-
%
Differential Phase (Notes 16, 17)
RL = 150Ω
25
-
0.03
-
°
Gain Flatness
To 5MHz
25
-
0.1
-
dB
NOTES:
5. Suggested VOS Adjust Circuit: The inverting input current (-IBIAS) can be adjusted with an external 10kΩ pot between pins 1 and 5, wiper
connected to V+. Since -IBIAS flows through the feedback resistor (RF), the result is an adjustment in offset voltage. The amount of offset voltage
adjustment is determined by the value of RF (ΔVOS = Δ-IBIAS*RF).
6. RL = 100Ω, VIN = 10V. This is the minimum current which must be pulled out of the Disable pin in order to disable the output. The output is
considered disabled when -10mV
≤ VOUT ≤ +10mV.
7. VIN = 0V. This is the maximum current that can be pulled out of the Disable pin with the HA-5020 remaining enabled. The HA-5020 is considered
disabled when the supply current has decreased by at least 0.5mA.
8. VOUT switches from -10V to +10V, or from +10V to -10V. Specification is from the 25% to 75% points.
9.
10. RL = 100Ω, VOUT = 1V. Measured from 10% to 90% points for rise/fall times; from 50% points of input and output for propagation delay.
11. This parameter is not tested. The limits are guaranteed based on lab characterization, and reflect lot-to-lot variation.
12. VIN = +10V, Disable = +15V to 0V. Measured from the 50% point of Disable to VOUT = 0V.
13. VIN = +10V, Disable = 0V to +15V. Measured from the 50% point of Disable to VOUT = 10V.
14. VIN = 0V, Force VOUT from 0V to ±10V, tR = tF = 50ns.
15. Measured with a VM700A video tester using a NTC-7 composite VITS.
16. See “Typical Performance Curves” on page 12 for more information.
17. VCM = ±2.5V. At -40°C product is tested at VCM = ±2.25V because short test duration does not allow self heating.
18. RL = 100Ω. VIN = 2.5V. This is the minimum current which must be pulled out of the Disable pin in order to disable the output. The output is
considered disabled when -10mV
≤ VOUT ≤ +10mV.
19. VOUT switches from -2V to +2V, or from +2V to -2V. Specification is from the 25% to 75% points.
20. FPBW =
.
21. VIN = 0V, Force VOUT from 0V to ±2.5V, tR = tF = 50ns.
22. VIN = +2V, Disable = +5V to 0V. Measured from the 50% point of Disable to VOUT = 0V.
23. VIN = +2V, Disable = 0V to +5V. Measured from the 50% point of Disable to VOUT = 2V.
Electrical Specifications
V+ = +5V, V- = -5V, RF = 1kΩ, AV = +1, RL = 400Ω, CL ≤10pF, Unless Otherwise Specified.
Parameters are not tested. The limits are guaranteed based on lab characterizations, and reflect
lot-to-lot variation. (Continued)
PARAMETER
TEST CONDITIONS
TEMP.
(°C)
MIN
TYP
MAX
UNITS
FPBW
Slew Rate
2
πV
PEAK
--------------------------- ;V
PEAK = 10V.
=
Slew Rate
2
πV
PEAK
--------------------------- ;V
PEAK =2V
HA-5020
相關PDF資料 |
PDF描述 |
|---|---|
| EL9202ILZ-T7 | IC AMP VCOM PROGRAMMABLE 24-QFN |
| MAX5253BCAP+T | IC DAC 12BIT QUAD 3V 20-SSOP |
| EL9200IL | IC AMP VCOM PROGRAMMABLE 12-DFN |
| MX7537JCWG+T | IC DAC 12BIT DL MULT 24-SOIC |
| MX7538KCWG+T | IC DAC 14BIT MPU COMP 24SOIC |
相關代理商/技術參數 |
參數描述 |
|---|---|
| HA3-5020-5Z | 功能描述:運算放大器 - 運放 W/ANNEAL OPAMP 100MH Z CFB DISABLE COM RoHS:否 制造商:STMicroelectronics 通道數量:4 共模抑制比（最小值）:63 dB 輸入補償電壓:1 mV 輸入偏流（最大值）:10 pA 工作電源電壓:2.7 V to 5.5 V 安裝風格:SMD/SMT 封裝 / 箱體:QFN-16 轉換速度:0.89 V/us 關閉:No 輸出電流:55 mA 最大工作溫度:+ 125 C 封裝:Reel |
| HA3-5020-9 | 制造商:未知廠家 制造商全稱:未知廠家 功能描述:Current-Feedback Operational Amplifier |
| HA3-5020R2548 | 制造商:Harris Corporation 功能描述: |
| HA350335 | 制造商:HAR 功能描述:350335 HAR'94 S10L2B 制造商:HARRIS 功能描述:IC S11L1C |
| HA3-5033-5 | 功能描述:IC VIDEO BUFFER 250MHZ 8-PDIP RoHS:否 類別:集成電路 (IC) >> 線性 - 放大器 - 視頻放大器和頻緩沖器 系列:- 標準包裝:1,000 系列:- 應用:驅動器 輸出類型:差分 電路數:3 -3db帶寬:350MHz 轉換速率:1000 V/µs 電流 - 電源:14.5mA 電流 - 輸出 / 通道:60mA 電壓 - 電源，單路/雙路(±):5 V ~ 12 V，±2.5 V ~ 6 V 安裝類型:表面貼裝 封裝/外殼:20-VFQFN 裸露焊盤 供應商設備封裝:20-QFN 裸露焊盤（4x4） 包裝:帶卷 (TR) |
發布緊急采購，3分鐘左右您將得到回復。