- 您現在的位置：買賣IC網 > PDF目錄383056 > GX214A (Electronic Theatre Controls, Inc.) GX214A Monolithic 4x1 Video Multiplexer PDF資料下載
參數資料
| 型號： | GX214A |
| 廠商： | Electronic Theatre Controls, Inc. |
| 英文描述： | GX214A Monolithic 4x1 Video Multiplexer |
| 中文描述： | GX214A單片4x1視頻復用器 |
| 文件頁數： | 3/5頁 |
| 文件大?。?/td> | 175K |
| 代理商： | GX214A |
520 - 5 - 1
3
INPUTS
VIDEO SWITCHES
V 0
V 1
V 2
V 3
75
75
75
75
0.1
1
2
6
5
4
3
7
9
10
11
12
13
14
8
1
2
6
5
4
3
7
9
10
11
12
13
14
8
V 4
V 5
V 6
V 7
75
75
75
75
0.1
0.1
0.1
-8V
-8V
+8V
+8V
A 0
A 1
A 2
IN 0
SG
IN 1
SG
IN 2
SG
IN 3
+V
A 0
A 1
CS
OUT
LG
-V
IN 0
SG
IN 1
SG
IN 2
SG
IN 3
+V
A 0
A 1
CS
OUT
LG
-V
ADDRESS
75
GAIN, OFFSET, FREQUENCY
RESPONSE ADJUSTMENTS
AMPLIFIER/BUFFER
VOUT
2.67 K
An external load current of 2 to 8mA should be supplied
from each output bus to negative supply. For most applications
a load resistor of 2.67k
, 1% is recommended to minimize
offset drift with temperature. In order to improve differential
phase and tighten the insertion loss tolerance, an external
constant current active load may be substituted for the
load resistor. Note however, that since only one GX214A
output drives the output bus at any one time, only one
external load is needed for the bus.
A typical application is shown below. Two GX214A ICs are
paralleled to form an 8x1 crosspoint matrix. The three
address lines make use of the A0, A1 and CS inputs. If more
than two devices are used in parallel, a decoder is necessary
in order to generate the extra address inputs.
Depending on the application and the speed of the logic
family used, latches may be required for synchronization
where timing delays are critical. The active switching
circuitry of the GX214A ensures low crosstalk and high per-
formance over an input voltage range of -1.2 to +5.0 volts.
Fig. 1 8x1 Video Multiplexer Incorporating Two GX214A Devices
APPLICATION INFORMATION
The circuit layout of any wideband circuit is critical. Good
high frequency design practice, proper lead dress and
PCB component placement along with a well regulated and
decoupled power supply will assure optimum performance
of the crosspoint.
The GX214A is non-inverting. The inputs are buffered and
require 75
line terminating resistors when driven from 75
cable. The inputs may be driven directly from an amplifier
which has low output impedance.
The output of the GX214A must be buffered to drive 7
lines. The addition of an amplifier/buffer also allows adjustments
to be made to the gain, offset and frequency response of
the circuit.
Signal Ground (SG) pins 2, 4 and 6 must be joined together
and preferably form part of a ground plane. The Signal
Ground must also be connected to the
±
8V power supply
ground. The potential of the Logic Ground (LG) pin 9 can
deviate from the Signal Ground by
±
0.5V maximum. Alternatively,
the signal and logic grounds can be joined together at one
point only.
All resistors in ohms, all capacitors
in microfarads, unless otherwise stated
相關PDF資料 |
PDF描述 |
|---|---|
| GX4201 | Wideband, Monolithic 1x1 Video Crosspoint Switch |
| GX4201-CDA | Wideband, Monolithic 1x1 Video Crosspoint Switch |
| GX4201-CKA | Wideband, Monolithic 1x1 Video Crosspoint Switch |
| GX4201-CTA | Wideband, Monolithic 1x1 Video Crosspoint Switch |
| GX4314L | GX4314L Low Power, Wideband 4 x 1 Video Multiplexer |
相關代理商/技術參數 |
參數描述 |
|---|---|
| GX214-ACDB | 制造商:Rochester Electronics LLC 功能描述: 制造商:Gennum Corporation 功能描述: |
| GX214-ACKB | 制造商:Gennum Corporation 功能描述: |
| GX214-ACKC | 制造商:未知廠家 制造商全稱:未知廠家 功能描述:GX214A Monolithic 4x1 Video Multiplexer |
| GX-21510-XX | 制造商:Gnodal, Inc 功能描述:QSFP40GIGABITETHERNETACTIVEOPTICALCABLE,10M - Bulk |
| GX-21515-XX | 制造商:Gnodal, Inc 功能描述:QSFP40GIGABITETHERNETACTIVEOPTICALCABLE,15M - Bulk |
發布緊急采購，3分鐘左右您將得到回復。