- 您現在的位置：買賣IC網 > PDF目錄385346 > GTL2008PW (NXP Semiconductors N.V.) 12-bit GTL to LVTTL translator with power good control and high-impedance LVTTL and GTL outputs PDF資料下載
參數資料
| 型號： | GTL2008PW |
| 廠商： | NXP Semiconductors N.V. |
| 元件分類： | 電壓/頻率轉換 |
| 英文描述： | 12-bit GTL to LVTTL translator with power good control and high-impedance LVTTL and GTL outputs |
| 封裝： | GTL2008PW<SOT361-1 (TSSOP28)|<<http://www.nxp.com/packages/SOT361-1.html<1<Always Pb-free,;GTL2008PW<SOT361-1 (TSSOP28)|<<http://www.nxp.com/packages/SOT361-1.html<1&l |
| 文件頁數： | 17/22頁 |
| 文件大?。?/td> | 191K |
| 代理商： | GTL2008PW |
GTL2008_4
All information provided in this document is subject to legal disclaimers.
NXP B.V. 2010. All rights reserved.
Product data sheet
Rev. 04 — 19 February 2010
17 of 22
NXP Semiconductors
GTL2008
GTL translator with power good control and high-impedance outputs
15.4 Reflow soldering
Key characteristics in reflow soldering are:
Lead-free versus SnPb soldering; note that a lead-free reflow process usually leads to
higher minimum peak temperatures (see
Figure 17
) than a SnPb process, thus
reducing the process window
Solder paste printing issues including smearing, release, and adjusting the process
window for a mix of large and small components on one board
Reflow temperature profile; this profile includes preheat, reflow (in which the board is
heated to the peak temperature) and cooling down. It is imperative that the peak
temperature is high enough for the solder to make reliable solder joints (a solder paste
characteristic). In addition, the peak temperature must be low enough that the
packages and/or boards are not damaged. The peak temperature of the package
depends on package thickness and volume and is classified in accordance with
Table 14
and
15
Table 14.
Package thickness (mm)
Table 15.
Package thickness (mm)
Moisture sensitivity precautions, as indicated on the packing, must be respected at all
times.
Studies have shown that small packages reach higher temperatures during reflow
soldering, see
Figure 17
.
SnPb eutectic process (from J-STD-020C)
Package reflow temperature (
°
C)
Volume (mm
3
)
< 350
235
220
≥
350
220
220
< 2.5
≥
2.5
Lead-free process (from J-STD-020C)
Package reflow temperature (
°
C)
Volume (mm
3
)
< 350
260
260
250
350 to 2000
260
250
245
> 2000
260
245
245
< 1.6
1.6 to 2.5
> 2.5
相關PDF資料 |
PDF描述 |
|---|---|
| GTL2010BS | 10-bit bidirectional low voltage translator |
| GTL2010PW | 10-bit bidirectional low voltage translator |
| GTL2012DP | 2-bit LVTTL to GTL transceiver |
| GTL2014PW | 4-bit LVTTL to GTL transceiver |
| GTL2018PW | 8-bit LVTTL to GTL transceiver |
相關代理商/技術參數 |
參數描述 |
|---|---|
| GTL2008PW,112 | 功能描述:轉換 - 電壓電平 12-BIT XEON GTL TO RoHS:否 制造商:Micrel 類型:CML/LVDS/LVPECL to LVCMOS/LVTTL 傳播延遲時間:1.9 ns 電源電流:14 mA 電源電壓-最大:3.6 V 電源電壓-最小:3 V 最大工作溫度:+ 85 C 安裝風格:SMD/SMT 封裝 / 箱體:MLF-8 |
| GTL2008PW,118 | 功能描述:轉換 - 電壓電平 12-BIT XEON GTL TO RoHS:否 制造商:Micrel 類型:CML/LVDS/LVPECL to LVCMOS/LVTTL 傳播延遲時間:1.9 ns 電源電流:14 mA 電源電壓-最大:3.6 V 電源電壓-最小:3 V 最大工作溫度:+ 85 C 安裝風格:SMD/SMT 封裝 / 箱體:MLF-8 |
| GTL2008PW-T | 功能描述:轉換 - 電壓電平 12-BIT XEON GTL TO LVTTL TRANS RoHS:否 制造商:Micrel 類型:CML/LVDS/LVPECL to LVCMOS/LVTTL 傳播延遲時間:1.9 ns 電源電流:14 mA 電源電壓-最大:3.6 V 電源電壓-最小:3 V 最大工作溫度:+ 85 C 安裝風格:SMD/SMT 封裝 / 箱體:MLF-8 |
| GTL2009 | 制造商:PHILIPS 制造商全稱:NXP Semiconductors 功能描述:3-bit GTL Front-Side Bus frequency comparator |
| GTL2009PW | 功能描述:校驗器 IC 3-BIT FSB FREQ CMPR RoHS:否 制造商:STMicroelectronics 產品: 比較器類型: 通道數量: 輸出類型:Push-Pull 電源電壓-最大:5.5 V 電源電壓-最小:1.1 V 補償電壓（最大值）:6 mV 電源電流（最大值）:1350 nA 響應時間: 最大工作溫度:+ 125 C 安裝風格:SMD/SMT 封裝 / 箱體:SC-70-5 封裝:Reel |
發布緊急采購，3分鐘左右您將得到回復。