- 您現在的位置：買賣IC網 > PDF目錄369691 > GTL2008 (NXP Semiconductors N.V.) 12-bit GTL to LVTTL translator with power good control and high-impedance LVTTL and GTL outputs PDF資料下載
參數資料
| 型號： | GTL2008 |
| 廠商： | NXP Semiconductors N.V. |
| 英文描述： | 12-bit GTL to LVTTL translator with power good control and high-impedance LVTTL and GTL outputs |
| 中文描述： | 12位的GTL的LVTTL與翻譯良好的控制權和高阻抗輸出LVTTL和GTL |
| 文件頁數： | 17/20頁 |
| 文件大?。?/td> | 102K |
| 代理商： | GTL2008 |
GTL2008_GTL2107_2
Koninklijke Philips Electronics N.V. 2006. All rights reserved.
Product data sheet
Rev. 02 — 26 September 2006
17 of 20
Philips Semiconductors
GTL2008; GTL2107
GTL translator with power good control and high-impedance outputs
–
larger than or equal to 1.27 mm, the footprint longitudinal axis is
preferred
to be
parallel to the transport direction of the printed-circuit board;
–
smaller than 1.27 mm, the footprint longitudinal axis
must
be parallel to the
transport direction of the printed-circuit board.
The footprint must incorporate solder thieves at the downstream end.
For packages with leads on four sides, the footprint must be placed at a 45
°
angle to
the transport direction of the printed-circuit board. The footprint must incorporate
solder thieves downstream and at the side corners.
During placement and before soldering, the package must be fixed with a droplet of
adhesive. The adhesive can be applied by screen printing, pin transfer or syringe
dispensing. The package can be soldered after the adhesive is cured.
Typical dwell time of the leads in the wave ranges from 3 seconds to 4 seconds at 250
°
C
or 265
°
C, depending on solder material applied, SnPb or Pb-free respectively.
A mildly-activated flux will eliminate the need for removal of corrosive residues in most
applications.
15.4 Manual soldering
Fix the component by first soldering two diagonally-opposite end leads. Use a low voltage
(24 V or less) soldering iron applied to the flat part of the lead. Contact time must be
limited to 10 seconds at up to 300
°
C.
When using a dedicated tool, all other leads can be soldered in one operation within
2 seconds to 5 seconds between 270
°
C and 320
°
C.
15.5 Package related soldering information
[1]
For more detailed information on the BGA packages refer to the (LF)BGA Application Note(AN01026);
order a copy from your Philips Semiconductors sales office.
[2]
All surface mount (SMD) packages are moisture sensitive. Depending upon the moisture content, the
maximum temperature (with respect to time) and body size of the package, there is a risk that internal or
external package cracks may occur due to vaporization of the moisture in them (the so called popcorn
effect). For details, refer to the Drypack information in the Data Handbook IC26; Integrated Circuit
Packages; Section: Packing Methods
Table 16.
Package
[1]
Suitability of surface mount IC packages for wave and reflow soldering methods
Soldering method
Wave
BGA, HTSSON..T
[3]
, LBGA, LFBGA, SQFP,
SSOP..T
[3]
, TFBGA, VFBGA, XSON
DHVQFN, HBCC, HBGA, HLQFP, HSO, HSOP,
HSQFP, HSSON, HTQFP, HTSSOP, HVQFN,
HVSON, SMS
PLCC
[5]
, SO, SOJ
LQFP, QFP, TQFP
SSOP, TSSOP, VSO, VSSOP
CWQCCN..L
[8]
, PMFP
[9]
, WQCCN..L
[8]
Reflow
[2]
suitable
not suitable
not suitable
[4]
suitable
suitable
not recommended
[5][6]
not recommended
[7]
not suitable
suitable
suitable
suitable
not suitable
相關PDF資料 |
PDF描述 |
|---|---|
| GTL2107 | 12-bit GTL to LVTTL translator with power good control and high-impedance LVTTL and GTL outputs |
| GTL2010PWDH | 10-bit GTL Processor Voltage Clamp |
| GTL2010 | 10-bit GTL processor voltage clamp(10位 GTL 鉗位電壓處理器) |
| GTL2014 | 4-bit LVTTL to GTL transceiver |
| GTL2021 | 32-bit GTL terminator with octal enables(帶八使能的32位 GTL 終端器) |
相關代理商/技術參數 |
參數描述 |
|---|---|
| GTL2008PW | 功能描述:轉換 - 電壓電平 12-BIT XEON GTL TO LVTTL TRANS RoHS:否 制造商:Micrel 類型:CML/LVDS/LVPECL to LVCMOS/LVTTL 傳播延遲時間:1.9 ns 電源電流:14 mA 電源電壓-最大:3.6 V 電源電壓-最小:3 V 最大工作溫度:+ 85 C 安裝風格:SMD/SMT 封裝 / 箱體:MLF-8 |
| GTL2008PW,112 | 功能描述:轉換 - 電壓電平 12-BIT XEON GTL TO RoHS:否 制造商:Micrel 類型:CML/LVDS/LVPECL to LVCMOS/LVTTL 傳播延遲時間:1.9 ns 電源電流:14 mA 電源電壓-最大:3.6 V 電源電壓-最小:3 V 最大工作溫度:+ 85 C 安裝風格:SMD/SMT 封裝 / 箱體:MLF-8 |
| GTL2008PW,118 | 功能描述:轉換 - 電壓電平 12-BIT XEON GTL TO RoHS:否 制造商:Micrel 類型:CML/LVDS/LVPECL to LVCMOS/LVTTL 傳播延遲時間:1.9 ns 電源電流:14 mA 電源電壓-最大:3.6 V 電源電壓-最小:3 V 最大工作溫度:+ 85 C 安裝風格:SMD/SMT 封裝 / 箱體:MLF-8 |
| GTL2008PW-T | 功能描述:轉換 - 電壓電平 12-BIT XEON GTL TO LVTTL TRANS RoHS:否 制造商:Micrel 類型:CML/LVDS/LVPECL to LVCMOS/LVTTL 傳播延遲時間:1.9 ns 電源電流:14 mA 電源電壓-最大:3.6 V 電源電壓-最小:3 V 最大工作溫度:+ 85 C 安裝風格:SMD/SMT 封裝 / 箱體:MLF-8 |
| GTL2009 | 制造商:PHILIPS 制造商全稱:NXP Semiconductors 功能描述:3-bit GTL Front-Side Bus frequency comparator |
發布緊急采購，3分鐘左右您將得到回復。