- 您現在的位置：買賣IC網 > PDF目錄384360 > GT3200-JN (STANDARD MICROSYSTEMS CORP) USB2.0 PJY IC PDF資料下載
參數資料
| 型號： | GT3200-JN |
| 廠商： | STANDARD MICROSYSTEMS CORP |
| 元件分類： | 網絡接口 |
| 英文描述： | USB2.0 PJY IC |
| 中文描述： | DATACOM, INTERFACE CIRCUIT, PQFP64 |
| 封裝： | 7 X 7 MM, 1.40 MM HEIGHT, TQFP-64 |
| 文件頁數： | 34/51頁 |
| 文件大?。?/td> | 1462K |
| 代理商： | GT3200-JN |
第1頁第2頁第3頁第4頁第5頁第6頁第7頁第8頁第9頁第10頁第11頁第12頁第13頁第14頁第15頁第16頁第17頁第18頁第19頁第20頁第21頁第22頁第23頁第24頁第25頁第26頁第27頁第28頁第29頁第30頁第31頁第32頁第33頁當前第34頁第35頁第36頁第37頁第38頁第39頁第40頁第41頁第42頁第43頁第44頁第45頁第46頁第47頁第48頁第49頁第50頁第51頁
USB2.0 PHY IC
Revision 1.3 (10-05-04)
29
SMSC GT3200, SMSC USB3250
DATASHEET
For HS operation, IDLE is a SE0 state on the bus. SE0 is also used to reset a HS device. A HS
device cannot use the 2.5us assertion of SE0 (as defined for FS operation) to indicate reset since the
bus is often in this state between packets. If no bus activity (IDLE) is detected for more than 3ms, a
HS device must determine whether the downstream facing port is signaling a suspend or a reset. The
following section details how this determination is made. If a reset is signaled, the HS device will then
initiate the HS Detection Handshake protocol.
8.5
Reset Detection
If a device in HS mode detects bus inactivity for more than 3ms (T1), it reverts to FS mode. This
enables the FS pull-up on the DP line in an attempt to assert a continuous FS J state on the bus. The
SIE must then check LINESTATE for the SE0 condition. If SE0 is asserted at time T2, then the
upstream port is forcing the reset state to the device (i.e., a Driven SE0). The device will then initiate
the HS detection handshake protocol.
8.6
Suspend Detection
If a HS device detects SE0 asserted on the bus for more than 3ms (T1), it reverts to FS mode. This
enables the FS pull-up on the DP line in an attempt to assert a continuous FS J state on the bus. The
Figure 8.1 Reset Timing Behavior (HS Mode)
Table 8.4 Reset Timing Values (HS Mode)
TIMING
PARAMETER
DESCRIPTION
VALUE
HS Reset T0
Bus activity ceases, signaling either a reset or a
SUSPEND.
0 (reference)
T1
Earliest time at which the device may place itself in
FS mode after bus activity stops.
HS Reset T0 + 3. 0ms < T1 < HS
Reset T0 + 3.125ms
T2
SIE samples LINESTATE. If LINESTATE = SE0, then
the SE0 on the bus is due to a Reset state. The
device now enters the HS Detection Handshake
protocol.
T1 + 100μs < T2 < T1 + 875μs
Driven SE0
HS Detection
Handshake
XCVRSELECT
DP/DM
TERMSELECT
time
Last
Activity
T2
T0
T1
相關PDF資料 |
PDF描述 |
|---|---|
| GT3200-JV | USB2.0 PJY IC |
| GTF701-HS3 | 2-Line EMI-Filter with ESD -Protection |
| GTF701-HS3-GS08 | 2-Line EMI-Filter with ESD -Protection |
| GTO1200-2R | Snubber Capacitors, Dry Self-healing |
| GTO2940-12RP | GTO Clamping Capacitors, Self-healing, Segmented |
相關代理商/技術參數 |
參數描述 |
|---|---|
| GT3200-JV | 制造商:Microchip Technology 功能描述:PHY 1-CH 12Mbps/480Mbps |
| GT3-2024SCF | 制造商:Hirose 功能描述: |
| GT3-2024SCF(70) | 制造商:Hirose 功能描述: |
| GT-32090-A0-PBN-C000 | 制造商:Marvell 功能描述: |
| GT3-20DP-2.5DSA | 制造商:HRS 制造商全稱:HRS 功能描述:Antenna, Sensor, and Communications Trunk Line Connections |
發布緊急采購，3分鐘左右您將得到回復。