- 您現在的位置：買賣IC網 > PDF目錄60615 > GSC24BC08 (GTM CORPORATION) 2-WIRE SERIAL EEPROMS PDF資料下載
參數資料
| 型號： | GSC24BC08 |
| 廠商： | GTM CORPORATION |
| 英文描述： | 2-WIRE SERIAL EEPROMS |
| 中文描述： | 2線串行EEPROM |
| 文件頁數： | 7/9頁 |
| 文件大?。?/td> | 305K |
| 代理商： | GSC24BC08 |
GSC24BC01/02/02/04/08/16
Page: 7/9
ISSUED DATE :2006/06/14
REVISED DATE :
Figure 9. Byte Write
Figure 10. Page Write
(
* = DON’T CARE bit for 1K)
Write Operations
Byte/Page Write:
If a write operation is entered (R/W=0) and an acknowledgment is sent, then the next sequence requires an
8-bit data word address. After an acknowledgment is received from this word address, the 1st byte of data can
be loaded. The device will send an acknowledgment after each byte to confirm the transmission.
To being the write cycle, a STOP condition must be issued (refer to Figure 9). Both byte and page write
operations are supported, so the STOP condition can be issued after the 1st byte or the last byte in the page.
When the STOP condition occurs, an internal time is started, all input are disabled, and the EEPROM will not
respond to any more commands until the write cycle is completed.
Note: The number of bytes in a page depends on the density used. If 1K density is used, then the page size is
8 bytes. In contrast, if the 16K density is used, then the page size is 16 bites. Refer to the Memory
Organization section for more details.
The internal page counter is incremented after each byte received, but the row location of the memory page
will always remain the same. Therefore, the device will wrap around to the 1st byte in the page after the last
byte in the page is received. Any further data loaded into the page buffer will overwrite the previous data
loaded.
Acknowledge Polling: After the STOP condition is issued, the write cycle begins. Acknowledge polling can be
initiated by sending a START condition followed by the device address word. If the EEPROM has completed
the internal write cycle and returned to standby mode, the device will respond by sending back an
acknowledgment by pulling the SDA pin low. Otherwise, the sequence will be ignored and no acknowledgment
will be sent.
Read Operations
There are three types of read operations: current address read, random address read, and sequence read. A
random address read can be considered a current address read operation with an additional sequence in the
beginning to load a different address into the internal counter. A sequential read occurs when subsequent
bytes are clocked out after a current address read or random address read occurs.
*
相關PDF資料 |
PDF描述 |
|---|---|
| GSC24BC16 | 2-WIRE SERIAL EEPROMS |
| GSC2596M | 150 KHz, 2A PWM Step-Down DC/DC Converter |
| GSC3842 | HIGH PERFORMANCE CURRENT MODE CONTROLERS |
| GSC3843 | HIGH PERFORMANCE CURRENT MODE CONTROLERS |
| GSC4081 | NPN EPITAXIAL PLANAR TRANSISTOR |
相關代理商/技術參數 |
參數描述 |
|---|---|
| GSC24BC16 | 制造商:GTM 制造商全稱:GTM 功能描述:2-WIRE SERIAL EEPROMS |
| GSC-24D/B | 制造商:Crydom 功能描述: |
| GSC25 | 制造商:SLPOWER 制造商全稱:SL Power Electronics 功能描述:25 Watt Global Performance Switchers |
| GSC2596M | 制造商:GTM 制造商全稱:GTM 功能描述:150 KHz, 2A PWM Step-Down DC/DC Converter |
| GSC25A | 功能描述:線性和開關式電源 25W +5.1/+12/-12V RoHS:否 制造商:TDK-Lambda 產品:Switching Supplies 開放式框架/封閉式:Enclosed 輸出功率額定值:800 W 輸入電壓:85 VAC to 265 VAC 輸出端數量:1 輸出電壓（通道 1）:20 V 輸出電流（通道 1）:40 A 商用/醫用: 輸出電壓（通道 2）: 輸出電流（通道 2）: 安裝風格:Rack 長度: 寬度: 高度: |
發布緊急采購，3分鐘左右您將得到回復。