參數資料
型號: GS881Z18T-100
廠商: GSI TECHNOLOGY
元件分類: DRAM
英文描述: 8Mb Pipelined and Flow Through Synchronous NBT SRAMs
中文描述: 512K X 18 ZBT SRAM, 12 ns, PQFP100
封裝: TQFP-100
文件頁數: 7/34頁
文件大小: 542K
代理商: GS881Z18T-100
Rev: 1.10 8/2000
Specifications cited are subject to change without notice. For latest documentation see http://www.gsitechnology.com
7/34
1998, Giga Semconductor, Inc.
Preliminary
.
GS881Z18/36T-11/100/80/66
Functional Details
Clocking
Deassertion of the Clock Enable (CKE) input blocks the Clock input from reaching the RAM's internal circuits. It may be used to
suspend RAM operations. Failure to observe Clock Enable set-up or hold requirements will result in erratic operation.
Pipeline Mode Read and Write Operations
All inputs (with the exception of Output Enable, Linear Burst Order and Sleep) are synchronized to rising clock edges. Single cycle
read and write operations must be initiated with the Advance/Load pin (ADV) held low, in order to load the new address. Device
activation is accomplished by asserting all three of the Chip Enable inputs (E
1
, E
2,
and E
3
). Deassertion of any one of the Enable
inputs will deactivate the device.
Read operation is initiated when the following conditions are satisfied at the rising edge of clock: CKE is asserted Low, all three
chip enables (E1, E2, and E3) are active, the write enable input signals W is deasserted high, and ADV is asserted low. The address
presented to the address inputs is latched in to address register and presented to the memory core and control logic. The control
logic determines that a read access is in progress and allows the requested data to propagate to the input of the output register. At
the next rising edge of clock the read data is allowed to propagate through the output register and onto the Output pins.
Write operation occurs when the RAM is selected, CKE is active and the Write input is sampled low at the rising edge of clock.
The Byte Write Enable inputs (B
A
, B
B
, B
C,
and B
D
) determine which bytes will be written. All or none may be activated. A Write
Cycle with no Byte Write inputs active is a no-op cycle. The pipelined NBT SRAM provides double late write functionality,
matching the write command versus data pipeline length (2 cycles) to the read command versus data pipeline length (2 cycles). At
the first rising edge of clock, Enable, Write, Byte Write(s), and Address are registered. The Data In associated with that address is
required at the third rising edge of clock.
Flow Through Mode Read and Write Operations
Operation of the RAM in Flow Through mode is very similar to operations in Pipeline mode. Activation of a Read Cycle and the
use of the Burst Address Counter is identical. In Flow Through mode the device may begin driving out new data immediately after
new address are clocked into the RAM, rather than holding new data until the following (second) clock edge. Therefore, in Flow
Through mode the read pipeline is one cycle shorter than in Pipeline mode.
Write operations are initiated in the same way as well, but differ in that the write pipeline is one cycle shorter, preserving the ability
to turn the bus from reads to writes without inserting any dead cycles. While the pipelined NBT RAMs implement a double late
write protocol, in Flow Through mode a single late write protocol mode is observed. Therefore, in Flow Through mode, address
and control are registered on the first rising edge of clock and data in is required at the data input pins at the second rising edge of
clock.
Function
W
B
A
B
B
B
C
B
D
Read
H
X
X
X
X
Write Byte “a”
L
L
H
H
H
Write Byte “b”
L
H
L
H
H
Write Byte “c”
L
H
H
L
H
Write Byte “d”
L
H
H
H
L
Write all Bytes
L
L
L
L
L
Write Abort/NOP
L
H
H
H
H
相關PDF資料
PDF描述
GS88218AB 512K x 18, 256K x 36 9Mb SCD/DCD Sync Burst SRAMs
GS88236AB-150I 512K x 18, 256K x 36 9Mb SCD/DCD Sync Burst SRAMs
GS88236AB-166 512K x 18, 256K x 36 9Mb SCD/DCD Sync Burst SRAMs
GS88236AB-166I 512K x 18, 256K x 36 9Mb SCD/DCD Sync Burst SRAMs
GS88236AB-200 512K x 18, 256K x 36 9Mb SCD/DCD Sync Burst SRAMs
相關代理商/技術參數
參數描述
GS881Z18T-100I 制造商:GSI 制造商全稱:GSI Technology 功能描述:8Mb Pipelined and Flow Through Synchronous NBT SRAMs
GS881Z18T-11 制造商:GSI 制造商全稱:GSI Technology 功能描述:8Mb Pipelined and Flow Through Synchronous NBT SRAMs
GS881Z18T-11I 制造商:GSI 制造商全稱:GSI Technology 功能描述:8Mb Pipelined and Flow Through Synchronous NBT SRAMs
GS881Z18T-66 制造商:GSI 制造商全稱:GSI Technology 功能描述:8Mb Pipelined and Flow Through Synchronous NBT SRAMs
GS881Z18T-66I 制造商:GSI 制造商全稱:GSI Technology 功能描述:8Mb Pipelined and Flow Through Synchronous NBT SRAMs