- 您現在的位置：買賣IC網 > PDF目錄223865 > GS81302TT07GE-333I (GSI TECHNOLOGY) 16M X 8 DDR SRAM, 0.45 ns, PBGA165 PDF資料下載
參數資料
| 型號： | GS81302TT07GE-333I |
| 廠商： | GSI TECHNOLOGY |
| 元件分類： | SRAM |
| 英文描述： | 16M X 8 DDR SRAM, 0.45 ns, PBGA165 |
| 封裝： | 15 X 17 MM, 1 MM PITCH, ROHS COMPLIANT, FPBGA-165 |
| 文件頁數： | 31/31頁 |
| 文件大?。?/td> | 1198K |
| 代理商： | GS81302TT07GE-333I |
第1頁第2頁第3頁第4頁第5頁第6頁第7頁第8頁第9頁第10頁第11頁第12頁第13頁第14頁第15頁第16頁第17頁第18頁第19頁第20頁第21頁第22頁第23頁第24頁第25頁第26頁第27頁第28頁第29頁第30頁當前第31頁
GS81302TT07/10/19/37E-450/400/350/333/300
Specifications cited are subject to change without notice. For latest documentation see http://www.gsitechnology.com.
Rev: 1.00 5/2011
9/31
2011, GSI Technology
FLXDrive-II Output Driver Impedance Control
HSTL I/O SigmaDDR-II+ SRAMs are supplied with programmable impedance output drivers. The ZQ pin must be connected to
VSS via an external resistor, RQ, to allow the SRAM to monitor and adjust its output driver impedance. The value of RQ must be
5X the value of the desired RAM output impedance. The allowable range of RQ to guarantee impedance matching continuously is
between 175
Ω and 350Ω. Periodic readjustment of the output driver impedance is necessary as the impedance is affected by drifts
in supply voltage and temperature. The SRAM’s output impedance circuitry compensates for drifts in supply voltage and
temperature. A clock cycle counter periodically triggers an impedance evaluation, resets and counts again. Each impedance
evaluation may move the output driver impedance level one step at a time towards the optimum level. The output driver is
implemented with discrete binary weighted impedance steps.
Input Termination Impedance Control
These SigmaQuad-II+ SRAMs are supplied with programmable input termination on Data (D), Byte Write (BW), and Clock (K,K)
input receivers. The input termination is always enabled, and the impedance is programmed via the same RQ resistor (connected
between the ZQ pin and VSS) used to program output driver impedance, in conjuction with the ODT pin (6R). When the ODT pin
is tied Low, input termination is "strong" (i.e., low impedance), and is nominally equal to RQ*0.3 Thevenin-equivalent when RQ is
between 175 and 350. When the ODT pin is tied High (or left floating—the pin has a small pull-up resistor), input termination
is "weak" (i.e., high impedance), and is nominally equal to RQ*0.6 Thevenin-equivalent when RQ is between 175 and 250.
Periodic readjustment of the termination impedance occurs to compensate for drifts in supply voltage and temperature, in the same
manner as for driver impedance (see above).
Note:
D, BW, K, K inputs should always be driven High or Low; they should never be tri-stated (i.e., in a High-Z state). If the inputs are
tri-stated, the input termination will pull the signal to VDDQ/2 (i.e., to the switch point of the diff-amp receiver), which could cause
the receiver to enter a meta-stable state, resulting in the receiver consuming more power than it normally would. This could result
in the device’s operating currents being higher.
相關PDF資料 |
PDF描述 |
|---|---|
| GS816036AGT-250I | 512K X 36 CACHE SRAM, 5.5 ns, PQFP100 |
| GS8160E36GT-250 | 512K X 36 CACHE SRAM, 5.5 ns, PQFP100 |
| GS816118AGT-200IT | 1M X 18 CACHE SRAM, 6.5 ns, PQFP100 |
| GS8161E18GT-166I | 1M X 18 CACHE SRAM, 7 ns, PQFP100 |
| GS8162V18AGB-350I | 1M X 18 CACHE SRAM, 4.5 ns, PBGA119 |
相關代理商/技術參數 |
參數描述 |
|---|---|
| GS815018AB | 制造商:GSI 制造商全稱:GSI Technology 功能描述:1M x 18, 512K x 36 18Mb Register-Register Late Write SRAM |
| GS815018AB-250 | 制造商:GSI Technology 功能描述:SRAM SYNC DUAL 2.5V 18MBIT 1MX18 2NS 119FPBGA - Trays |
| GS815018AB-250I | 制造商:GSI Technology 功能描述:SRAM SYNC DUAL 2.5V 18MBIT 1MX18 2NS 119FPBGA - Trays |
| GS815018AB-300 | 制造商:GSI Technology 功能描述:SRAM SYNC DUAL 2.5V 18MBIT 1MX18 1.6NS 119FPBGA - Trays |
| GS815018AB-300I | 制造商:GSI Technology 功能描述:SRAM SYNC DUAL 2.5V 18MBIT 1MX18 1.6NS 119FPBGA - Trays |
發布緊急采購，3分鐘左右您將得到回復。