- 您現在的位置：買賣IC網 > PDF目錄370378 > GS-D200S (意法半導體) 2/2.5A Bipolar Stepper Motor Driver Modules(2/2.5A雙極型步進電機驅動器模塊) PDF資料下載
參數資料
| 型號： | GS-D200S |
| 廠商： | 意法半導體 |
| 英文描述： | 2/2.5A Bipolar Stepper Motor Driver Modules(2/2.5A雙極型步進電機驅動器模塊) |
| 中文描述： | 2/2.5A雙極步進電機驅動器模塊（2/2.5A雙極型步進電機驅動器模塊） |
| 文件頁數： | 5/17頁 |
| 文件大?。?/td> | 183K |
| 代理商： | GS-D200S |
第1頁第2頁第3頁第4頁當前第5頁第6頁第7頁第8頁第9頁第10頁第11頁第12頁第13頁第14頁第15頁第16頁第17頁
5/17
PIN DESCRIPTION
Pin
Function
Description
1
GND1
Return path for the logic signals and 5V supply.
2
Sync
Chopper oscillatoroutput.
Several modules can be synchronized by connectingtogether all Sync pins. This pin can
be used as the input for an external clock source.
3
Reset
Asynchronousreset input. An active low pulse on this input preset theinternal logic to the
initial state (ABCD=0101).
4
Half/Full
Half/Full stepselection input.
When high or unconnectedthe half stepoperation is selected.
5
Home
When high, this output indicatesthat the internal counteris in its initial state (ABCD=0101).
This signal may be usedin conjunctionwith a mechanical switch to groundor with open
collector output of an optical detector to be used as a systemhome detector.
6
Stepclk
The motor is movedone step on the risingedge of this signal.
7
CW/CCW
Direction control input. When high or unconnected clockwise rotation is selected.Physical
direction of motor rotationdepends also on windings connection.
8
Oscillator
The chopper oscillatortiming, internally fixed at 17kHz,can be modified byconnecting a
resistor between this pin and Vss or a capacitor between this pin and Gnd1.
The oscillatorinput mustbe grounded when the unit is externally synchronized.
9
Ioset
Phase current setting input. Aresistor connectedbetween this pin and Gnd1 or Vss,
allows the factory setted phase currentvalue (1Afor GS-D200and 2Afor GS-D200S) to
be changed.
10
Control
Logic input thatallows the phase current decay mode selection. When high or
unconnected the slow decay is selected.
11
Enable
Module enable input. When low this input floats the outputsenabling the manual
positioning of the motor. Must be LOW duringpower-up and down sequence, HIGH during
normal operation.
12
Vss
5V supplyinput. Maximum voltage must not exceed7V.
13
GND2
Return path for the power section.
14
D
D output.
15
C
C output.
16
B
B output.
17
A
A output.
18
Vs
Module and motor supply voltage.
Maximum voltage must not exceed the specified values.
GS-D200/GS-D200S
相關PDF資料 |
PDF描述 |
|---|---|
| GS-D500A | 100V/5A STEP AND MICROSTEP DRIVE BOARD FOR STEPPER MOTORS |
| GS-DC200 | STEPPER MOTOR CONTROL AND DRIVE SYSTEM FAMILY |
| GS-DC200S | STEPPER MOTOR CONTROL AND DRIVE SYSTEM FAMILY |
| GS-DC200SS | STEPPER MOTOR CONTROL AND DRIVE SYSTEM FAMILY |
| GS-F8MB-SIMM | 8MByte SIMM Flash Memory Module(8M字節SIMM閃速存儲器模塊) |
相關代理商/技術參數 |
參數描述 |
|---|---|
| GSD-250 | 功能描述:自耦變壓器 230Vin 115Vout 50/60Hz 2.2A 250VA RoHS:否 制造商:Hammond Manufacturing 功率額定值:1.5 KVA 初級電壓額定值: 次級電壓額定值: 安裝風格: 長度: 寬度:111.76 mm 高度:136.91 mm |
| GSD2656 | 制造商:GTM 制造商全稱:GTM 功能描述:NPN EPITAXIAL TRANSISTOR |
| GSD-300 | 制造商:Stancor 功能描述:Power Transformer 1500Vrms 230V Prim. 115V Sec. Flange Mount |
| GSD304020GP2 | 制造商:Pentair Technical Products / Hoffman 功能描述:GLOBAL WALL-MOUNT ENCLOSURE, GLAND P 制造商:PENTAIR TECNICAL PRODCUTS 功能描述:GLOBAL WALL-MOUNT ENCLOSURE, GLAND P |
| GSD-329 | 制造商:Duratool 功能描述:All-in-One Screwdriver and Bit Set with Wire Stripper |
發布緊急采購，3分鐘左右您將得到回復。