- 您現在的位置：買賣IC網 > PDF目錄384342 > GP2W0002YP (Sharp Corporation) IrDA 1.2 Type Compliant Optical Data Communication 115 kbps Transceiver(IrDA 1.2 兼容的光數字通信115 kbps 收發器) PDF資料下載
參數資料
| 型號： | GP2W0002YP |
| 廠商： | Sharp Corporation |
| 英文描述： | IrDA 1.2 Type Compliant Optical Data Communication 115 kbps Transceiver(IrDA 1.2 兼容的光數字通信115 kbps 收發器) |
| 中文描述： | 紅外1.2類型兼容光115 kbps的數據通信收發器（紅外線1.2兼容的光數字通信115 kbps的收發器） |
| 文件頁數： | 1/15頁 |
| 文件大?。?/td> | 104K |
| 代理商： | GP2W0002YP |
IrDA Data Sheet
1
GP2W0002YP
115 kbps Transceiver
IrDA Data Sheet
FEATURES
Built-in Photodiode
Operating voltage 2.7 V to 5.5 V
In circuit design, make allowance for the degradation
of light emitting diode output that results from long
continuous operation (50% degradation/5 years).
This product shall not contain the following materi-
als, and these materials shall not be used in the pro-
duction process for this product.
– CFC
S
– Halon
– Carbon Tetrachloride
– 1.1.1. Trichloroethane (Methylchloroform)
– Specific brominated flame retardants such as the
PBBO
S
and PBB
S
are not used in this device.
INTRODUCTION
This specification applies to the outline and charac-
teristics of IrDA 1.2 type (data rate 2.4 kbps to
115.2 kbps, low power option compliant) optical data
communication transceiver.
NOTES
Caution should be taken to prevent the detector sur-
face from being smeared with dust or dirt, or from
being touched, as it may cause faulty operation.
Cleaning conditions:
– Solvent cleaning: Solvent temperature 45°C or
less. Immersion for 3 minutes or less.
– Ultrasonic cleaning: The effect of ultrasonic
cleaning on the device differs by cleaning bath
size, ultrasonic power output, cleaning time, PCB
size or device mounting condition, etc. Test the
device under actual conditions and confirm that
ultrasonic cleaning does not cause any immedi-
ate or potential defects.
– Cleaning solvent: The cleaning shall be carried
out with ethyl alcohol, methyl alcohol, or isopropyl
alcohol.
In order to prevent electrostatic damage to the inte-
grated circuit, handle this device in a static-free envi-
ronment and workstation.
External force applied to the device after mounting can
cause mounting defects such as the terminal coming
off. Be careful when handling the device and prevent
objects from touching the device after mounting.
Refer to the ‘Precautions for Soldering’ section.
When the system (program) is designed, the turn
around time from transmit to receive should be
designed by considering 200 μs or more that is spec-
ified by IrDA. This turn around time means the time
that this device does not temporarily detect the
incoming signal, since the transmitted light from the
transmitter side reaches the detector side of the
same transceiver.
Consider that 200 μs or more (at T
A
= 25°C, no input
signal) is necessary to return from shut-down mode
to ready-operation mode. In addition, thoroughly
confirm the operation in the actual application.
When there is considerable external stray light or a
light source is located near the transceiver, or the
detector face receives considerable external stray
light, a pulse other than desired signal output may be
generated as noise on output terminal of the trans-
ceiver. Consider the layout and structure in your
design to minimize disturbing light on the detector face.
When the sensor is adopted in an IR communication
system, it should be used according to the signal
method which is specified by ‘Serial Infrared Physi-
cal Layer Link Specification’ published by the Infra-
red Data Association. Faulty operation may occur, if
a signal method other than that specified is used.
Figure 1. Recommended External Circuit
1
LEDA
RL
R
2
CX
2
CX
1
R
1
2
TXD
3
SD
SD
TX
4
RXD
RXD
GP2W0002YP-1
5
GND
6
V
CC
V
CC
+
COMPONENTS
NOTE:
Choose the most suitable CX
and R
according to
the noise level and noise frequency of power supply.
RECOMMENDED VALUES
CX
1
CX
2
R
1
R
2
47
μ
F/6.3 V (NOTE)
RL
(STANDARD)
RL
(LOW POWER)
1500 pF/25 V
47
±
5%, 1/10 W (NOTE)
1 k
±
5%, 1/10 W
2.2
±
5%, 1/2 W
(V
CC
= 3.0 V, I
E
= 40 mW/sr)
33
±
1%, 1/8 W
(V
CC
= 3.0 V, I
E
= 3.6 mW/sr)
相關PDF資料 |
PDF描述 |
|---|---|
| GP2W0104YP | 115 kbps Transceiver |
| GP2W0106YP | IrDA 1.2 Type Compliant Optical Data Communication 115 kbps Transceiver(IrDA 1.2 兼容的光數字通信115 kbps 收發器) |
| GP2W0110YP | TECHNICAL LITERATURE FOR Optical Data communication transceiver |
| GP2W1001YP | DEVICE SPECIPICATION FOR OPTICAL DATA COMMUNICATION TRANSCEIVER |
| GP2W2001YK | IrDA Control Infrared Transceiver(IrDA控制紅外收發器) |
相關代理商/技術參數 |
參數描述 |
|---|---|
| GP2W0004XP | 功能描述:MODULE IRDA 115.2KBPS 6SMD RoHS:否 類別:傳感器，轉換器 >> IrDA 收發器模塊 系列:* 產品變化通告:Product Discontinuation 30/Sept/2009 產品目錄繪圖:GP2W Series 標準包裝:1 系列:* 數據速率:115.2kbs（SIR） 電源電壓:2.4 V ~ 3.6 V 無效電流，標準值@ 25° C:70µA 通信距離，低功率:20cm 方向:側視圖 工作溫度:-40°C ~ 85°C 尺寸:8.3mm x 2.1mm x 1.7mm 標準:IrPHY 1.4 關機:* 包裝:Digi-Reel® 其它名稱:425-2614-6 |
| GP2W0004XP0F | 功能描述:MODULE IRDA 115.2KBPS 6SMD RoHS:是 類別:傳感器，轉換器 >> IrDA 收發器模塊 系列:* 產品變化通告:Product Discontinuation 30/Sept/2009 產品目錄繪圖:GP2W Series 標準包裝:1 系列:* 數據速率:115.2kbs（SIR） 電源電壓:2.4 V ~ 3.6 V 無效電流，標準值@ 25° C:70µA 通信距離，低功率:20cm 方向:側視圖 工作溫度:-40°C ~ 85°C 尺寸:8.3mm x 2.1mm x 1.7mm 標準:IrPHY 1.4 關機:* 包裝:Digi-Reel® 其它名稱:425-2614-6 |
| GP2W0004YP | 功能描述:IRDA MODULE 115.2KBPS 6SMD RoHS:否 類別:傳感器，轉換器 >> IrDA 收發器模塊 系列:* 產品變化通告:Product Discontinuation 30/Sept/2009 產品目錄繪圖:GP2W Series 標準包裝:1 系列:* 數據速率:115.2kbs（SIR） 電源電壓:2.4 V ~ 3.6 V 無效電流，標準值@ 25° C:70µA 通信距離，低功率:20cm 方向:側視圖 工作溫度:-40°C ~ 85°C 尺寸:8.3mm x 2.1mm x 1.7mm 標準:IrPHY 1.4 關機:* 包裝:Digi-Reel® 其它名稱:425-2614-6 |
| GP2W0004YP0F | 功能描述:IRDA MODULE 115.2KBPS 6SMD RoHS:是 類別:傳感器，轉換器 >> IrDA 收發器模塊 系列:* 產品變化通告:Product Discontinuation 30/Sept/2009 產品目錄繪圖:GP2W Series 標準包裝:1 系列:* 數據速率:115.2kbs（SIR） 電源電壓:2.4 V ~ 3.6 V 無效電流，標準值@ 25° C:70µA 通信距離，低功率:20cm 方向:側視圖 工作溫度:-40°C ~ 85°C 尺寸:8.3mm x 2.1mm x 1.7mm 標準:IrPHY 1.4 關機:* 包裝:Digi-Reel® 其它名稱:425-2614-6 |
| GP2W0104YP | 制造商:SHARP 制造商全稱:Sharp Electrionic Components 功能描述:115 kbps Transceiver |
發布緊急采購，3分鐘左右您將得到回復。