參數資料
型號： GMS81516BTK
廠商： Hynix Semiconductor Inc.
元件分類： 8位微控制器
英文描述： 8-BIT SINGLE-CHIP MICROCONTROLLERS
中文描述： 8位單晶片微控制器
文件頁數： 65/110頁
文件大?。?/td> 1980K
代理商： GMS81516BTK
GMS81508B/16B/24B, GMS82512/16/24
62
MAY. 2001 Ver 2.0
16.1 Interrupt Sequence
An interrupt request is held until the interrupt is accepted
or the interrupt latch is cleared to “0” by a reset or an in-
struction. Interrupt acceptance sequence requires 8
f
XIN
(2
μ
s at f
MAIN
=4.19MHz) after the completion of the current
instruction execution. The interrupt service task is termi-
nated upon execution of an interrupt return instruction
[RETI].
Interrupt acceptance
1. The interrupt master enable flag (I-flag) is cleared to
“0” to temporarily disable the acceptance of any follow-
ing maskable interrupts. When a non-maskable inter-
rupt is accepted, the acceptance of any following
interrupts is temporarily disabled.
2. Interrupt request flag for the interrupt source accepted is
cleared to “0”.
3. The contents of the program counter (return address)
and the program status word are saved (pushed) onto the
stack area. The stack pointer decreases 3 times.
4. The entry address of the interrupt service program is
read from the vector table address and the entry address
is loaded to the program counter.
5. The instruction stored at the entry address of the inter-
rupt service program is executed.
Figure 16-4 Timing chart of Interrupt Acceptance and Interrupt Return Instruction
A interrupt request is not accepted until the I-flag is set to
“1” even if a requested interrupt has higher priority than
that of the current interrupt being serviced.
When nested interrupt service is required, the I-flag should
be set to “1” by “EI” instruction in the interrupt service
program. In this case, acceptable interrupt sources are se-
lectively enabled by the individual interrupt enable flags.
Saving/Restoring General-purpose Register
During interrupt acceptance processing, the program
counter and the program status word are automatically
saved on the stack, but accumulator and other registers are
not saved itself. These registers are saved by the software
if necessary. Also, when multiple interrupt services are
nested, it is necessary to avoid using the same data memory
V.L.
System clock
Address Bus
PC
SP
SP-1
SP-2
V.H.
New PC
V.L.
Data Bus
Not used
PCH
PCL
PSW
ADL
OP code
ADH
Instruction Fetch
Internal Read
Internal Write
Interrupt Processing Step
Interrupt Service Task
V.L. and V.H. are vector addresses.
ADL and ADH are start addresses of interrupt service routine as vector contents.
Basic Interval Timer
Vector Table Address
012
H
0E3
H
0FFE6
H
0FFE7
H
0E
H
2E
H
0E312
H
0E313
H
Entry Address
Correspondence between vector table address for BIT interrupt
and the entry address of the interrupt service program.
相關PDF資料
PDF描述
GMS81516BTLQ 8-BIT SINGLE-CHIP MICROCONTROLLERS
GMS81516BTQ 8-BIT SINGLE-CHIP MICROCONTROLLERS
GMS81524 8-BIT SINGLE-CHIP MICROCONTROLLERS
GMS81524BK 8-BIT SINGLE-CHIP MICROCONTROLLERS
GMS81524BQ 8-BIT SINGLE-CHIP MICROCONTROLLERS
相關代理商/技術參數
參數描述
GMS81516BTLQ 制造商:HYNIX 制造商全稱:Hynix Semiconductor 功能描述:8-BIT SINGLE-CHIP MICROCONTROLLERS
GMS81516BTQ 制造商:HYNIX 制造商全稱:Hynix Semiconductor 功能描述:HYUNDAI MICRO ELECTRONICS 8-BIT SINGLE-CHIP MICROCONTROLLERS
GMS81524 制造商:HYNIX 制造商全稱:Hynix Semiconductor 功能描述:8-BIT SINGLE-CHIP MICROCONTROLLERS
GMS81524B 制造商:HYNIX 制造商全稱:Hynix Semiconductor 功能描述:8-BIT SINGLE-CHIP MICROCONTROLLERS
GMS81524BK 制造商:HYNIX 制造商全稱:Hynix Semiconductor 功能描述:8-BIT SINGLE-CHIP MICROCONTROLLERS
發布緊急采購，3分鐘左右您將得到回復。

采購需求

(若只采購一條型號，填寫一行即可)

發布成功！您可以繼續發布采購。也可以進入我的后臺，查看報價

發布成功！您可以繼續發布采購。也可以進入我的后臺，查看報價

*型號 *數量 廠商 批號 封裝
添加更多采購

我的聯系方式

*
*
*