- 您現在的位置：買賣IC網 > PDF目錄382976 > FX633P1 (Electronic Theatre Controls, Inc.) Call Progress Tone Detector PDF資料下載
參數資料
| 型號： | FX633P1 |
| 廠商： | Electronic Theatre Controls, Inc. |
| 英文描述： | Call Progress Tone Detector |
| 中文描述： | 呼叫進展音探測器 |
| 文件頁數： | 7/12頁 |
| 文件大?。?/td> | 331K |
| 代理商： | FX633P1 |
Call Progress Tone Detector
FX633
1996 Consumer Microcircuits Limited
7
D/633/3
1.5.3
Block Diagram Description
(reference Figure 1)
Slicer
The input signal to the slicer is amplified by a self-biased inverting amplifier. The dc bias of this input is
internally set at V
DD.
Signal Analyser
The frequency range, quality and consistency of the input signal is analysed by this functional block. To
be classified as a call progress signal the input signal frequencies should lie between 340Hz and
650Hz. The signal to noise ratio must be 16dB or greater. The signal must be consistent over a period
of about 140 ms. These decode criteria are continuously monitored and the assessment is updated
every 7 ms, reference Figure 3.
The analyser samples the call progress signal at 9.3kHz; so care should be taken to avoid high
frequency signals (e.g. 18kHz) aliasing into the call progress band.
Control Logic
This block categorises the nature of the signal into various decoded output states and controls the two
output pins. See the Decode Output Truth Table in section 1.5.4.
Xtal/Clock Oscillator
If the on-chip Xtal oscillator is to be used, then external components X1, R1, C1 and C2 are required.
If an external clock source is to be used, then it should be connected to the XTAL/CLOCK input pin
and the XTALN pin should be left unconnected.
1.5.4
Decode Output Truth Table
DETECT2
DETECT1
CONDITIONS
0
0
No Signal
0
1
Call Progress Low Band:
Will detect 350+440, 400+450, 440+480,
400, 425, 440, and 450Hz tones
1
1
Call Progress High Band:
Will detect 480+620, 600 and 620Hz tones
1
0
Non Call Progress signal, e.g. Voice Activity
Note that DETECT1 responds to the whole range of call progress tones from 340Hz to 650Hz.
1.6
Application Notes
1.6.1
General
On power-up, a logic "0" at the ENABLE input may be used to disable and initialise the
device.
相關PDF資料 |
PDF描述 |
|---|---|
| FX802 | DC-DC Converter |
| FX803 | DC-DC Converter |
| FX851 | DC-DC Converter Applications |
| FX852 | DC-DC Converter Applications |
| FX853 | DC-DC Converter Applications |
相關代理商/技術參數 |
參數描述 |
|---|---|
| FX-638M | 制造商:Foxconn 功能描述:Black Micro ATX Tower Computer Case with 350W Power Supply 制造商:Foxconn 功能描述:BLACK MICRO ATX TOWER CASE 350W POWER SUPPLY |
| FX6-40P-0.8SV | 功能描述:CONN HEADER 40POS .8MM SMD GOLD RoHS:否 類別:連接器，互連式 >> 板對板 - 陣列，邊緣類型，包廂 系列:FX6 標準包裝:16 系列:FX6 連接器類型:接頭，外罩觸點 位置數:60 間距:0.031"（0.80mm） 行數:2 安裝類型:表面貼裝 特點:板導軌 觸點表面涂層:金 觸點涂層厚度:- 包裝:管件 配接層疊高度:6mm，8mm 板上方高度:0.236"（6.00mm） 其它名稱:*FX6-60P-0.8SV1H2417 |
| FX6-40P-0.8SV(22) | 制造商:Hirose 功能描述: |
| FX6-40P-0.8SV(71) | 功能描述:板對板與夾層連接器 HDR 40 POS 0.8mm Solder ST SMD Stick RoHS:否 制造商:JAE Electronics 系列:WP3 產品類型:Receptacles 節距:0.4 mm 疊放高度:1 mm 安裝角: 位置/觸點數量:50 排數:2 外殼材料:Plastic 觸點材料:Copper Alloy 觸點電鍍:Gold 電壓額定值:50 V 電流額定值:0.4 A |
| FX6-40P-0.8SV(92) | 功能描述:板對板與夾層連接器 40P M HEADER SMT BOARD VERTICAL TYPE RoHS:否 制造商:JAE Electronics 系列:WP3 產品類型:Receptacles 節距:0.4 mm 疊放高度:1 mm 安裝角: 位置/觸點數量:50 排數:2 外殼材料:Plastic 觸點材料:Copper Alloy 觸點電鍍:Gold 電壓額定值:50 V 電流額定值:0.4 A |
發布緊急采購，3分鐘左右您將得到回復。