
5
Specification
Absolute Maximum Ratings
Exceeding the maximum rating can result in device damage. Operation of the device outside the operating limits
is not implied.
Supply voltage
Input voltage at any pin (ref V
SS
= 0V)
Sink/source current (supply pins)
(other pins)
Total device dissipation @ T
AMB
25°C
Derating
Storage temperature range:
FX623P
-0.3 to 7.0V
-0.3 to (V
DD
+ 0.3V)
+/- 30mA
+/- 20mA
800mW Max.
10mW/°C
-40°C to +85°C (plastic)
Operating Limits ......
Supply Voltage (V
)
Operating Temperature ......
All device characteristics are measured under the following conditions unless otherwise specified:
V
DD
= 3.3V, T
OP
= -40 to +85 °C. Audio Level 0dB ref: = 775mVrms. Xtal/Clock Frequency = 3.579545MHz
Characteristics
See Note
Static Values
Supply Current
Input Logic “1”
Input Logic “0”
Output Logic “1”
Output Logic “0”
Impedance
CS and PURS Input
Hold Input
1
Signal Input
IRQ Output (logic “1”)
IRQ Output (logic “0”)
Q0 - Q3 & Data-Change Outputs (logic “1”)
Q0 - Q3 & Data-Change Outputs (logic “0”)
Q0 - Q3 & Data-Change Outputs (high Z)
Dynamic Values
Signal Input Range
2, 5
Decode Bandedge Tolerance
3
Xtal Inverter
Voltage Gain
Input Impedance
Output Impedance
Decoder Timing -
Figures 3 and 4
Power Up Reset Time
t
PURS
Data 'E' Time
t
DE
N
OTONE
to Tone Response Time
t
RESP
4
Tone to N
OTONE
Response Time
t
NT
4
Data to Data-Change Pulse Time
t
DC
Data-Change Pulse Width
t
PUL
Hold to Data-Change Rise Time
t
HOLD
HOLD to Data-Change Fall Time
t
NORM
IRQ Tone Response Time
t
RIRQ
IRQ Reset Time
t
IR
Data Access Time
t
ACS
CS High to Output Tri-State Time
t
HIZ
Min.
3.0
-40
Max.
5.5
+85
Unit
V
°C
at 25°C
Min.
Typ.
Max.
Unit
-
0.6
-
-
-
-
1.0
-
0.3
-
0.2
mA
%V
DD
%V
DD
%V
DD
%V
DD
0.7
-
0.8
-
10.0
0.5
0.1
-
-
-
-
1.0
-
-
-
-
-
-
M
M
M
k
k
M
30.0
175
0.7
175
-
100
500
2.0
500
-
35.0
-1.0
1,166
1.0
mVrms
%
-
20.0
10.0
-
-
-
-
-
-
V/V
M
k
160
2.5
31.0
-
-
0.625
-
63.0
-
-
-
-
-
-
-
-
-
ms
ms
ms
ms
ms
ms
μs
μs
ms
ns
ns
ns
27.0
-
-
1.25
-
-
29.0
-
-
-
50.0
60.0
1.15
-
-
150
52.0
250
250
100
Notes
1. This pin has an on-chip 1.0M
pullup resistor.
2. An a.c. coupled sine or squarewave.
3. See Table 1, Tone Decode Frequencies.
4. Delay between the change of input (Tone/N
OTONE
) and the change at the Q0 - Q3 outputs.
5. The signal input maximum value is determined by the formula V
DD
/2.83.