參數資料
型號： FTRJ8519U1KNL
元件分類： 光收發
英文描述： FIBER OPTIC TRANSCEIVER, 830-860nm, 2125Mbps(Tx), 2125Mbps(Rx), THROUGH HOLE MOUNT, LC CONNECTOR
文件頁數： 12/15頁
文件大?。?/td> 356K
代理商： FTRJ8519U1KNL
FTRJ8519U1xNL 2x6 Pin SFF Product Specification – March 2005
Finisar Corporation March 23, 2005 Rev D
Page 6
VIII. Digital Diagnostic Functions
Finisar FTRJ8519U1xNL 2x6 transceivers provide a unique digital diagnostic monitoring
interface, which allows real-time access to device operating parameters such as
transceiver temperature, laser bias current, transmitted optical power, received optical
power and transceiver supply voltage. It also defines a sophisticated system of alarm and
warning flags, which alerts end-users when particular operating parameters are outside of
a factory set normal range.
In order to access the digital diagnostics functionality, the transceivers have a 2-wire
serial communication protocol that is similar to that defined in the SFP MSA4. The
digital diagnostic monitoring interface makes use of the 8 bit address 1010001X (A2h)
only. The memory map for this interface is defined below. Additional information,
including details on the electrical interface, is described in Finisar Application Note AN-
2030: “Digital Diagnostics Monitoring Interface for SFP Optical Transceivers”. (Note:
only pages 17-35 of this Application note, including Section 4 are relevant to Finisar 2x6
transceivers.)
The standard SFP MSA serial ID provides access to identification information that
describes the transceiver’s capabilities, standard interfaces, manufacturer, and other
information. Finisar 2x6 transceivers provide access to a condensed version of this
information, over the 2-wire serial interface at the 8 bit address 1010000X (A2h) in bytes
128-190.
The operating and diagnostics information is monitored and reported by a Digital
Diagnostics Transceiver Controller (DDTC) inside the transceiver, which is accessed
through the 2-wire serial interface. When the serial protocol is activated, the serial clock
signal (SCL) is generated by the host. The positive edge clocks data into the 2x6
transceiver into those segments of the E2PROM that are not write-protected. The
negative edge clocks data from the 2x6 transceiver. The serial data signal (SDA) is bi-
directional for serial data transfer. The host uses SDA in conjunction with SCL to mark
the start and end of serial protocol activation. The memories are organized as a series of
8-bit data words that can be addressed individually or sequentially.
Digital diagnostics for the FTRJ8519U1xNL are internally calibrated by default.
相關PDF資料
PDF描述
FTRJ8519U1GNL FIBER OPTIC TRANSCEIVER, 830-860nm, 2125Mbps(Tx), 2125Mbps(Rx), THROUGH HOLE MOUNT, LC CONNECTOR
FTRX-1411D3 FIBER OPTIC TRANSCEIVER, 1260-1355nm, 10500Mbps(Tx), 10500Mbps(Rx), PANEL MOUNT, LC CONNECTOR
FTRX-1411M3 FIBER OPTIC TRANSCEIVER, 1290-1330nm, 10700Mbps(Tx), 10700Mbps(Rx), PANEL MOUNT, LC CONNECTOR
FTRX-1611-3 FIBER OPTIC TRANSCEIVER, 1530-1565nm, 10700Mbps(Tx), 10700Mbps(Rx), BOARD/PANEL MOUNT, LC CONNECTOR
FTRX-1811-3 FIBER OPTIC TRANSCEIVER, 1530-1565nm, 10700Mbps(Tx), 10700Mbps(Rx), PANEL MOUNT, LC CONNECTOR
相關代理商/技術參數
參數描述
FTRJ8524P2BNV 制造商:Finisar Corporation 功能描述:
FTRJ8524P2WNV 制造商:Finisar Corporation 功能描述:
FTR-JR 制造商:FUJITSU 制造商全稱:Fujitsu Component Limited. 功能描述:POWER RELAY 1 POLE 16 A-SLIM POWER RELAY
FTR-JRJB012W 功能描述:通用繼電器 POWER RoHS:否 制造商:Omron Electronics 觸點形式:1 Form A (SPST-NO) 觸點電流額定值:150 A 線圈電壓:24 VDC 線圈電阻:144 Ohms 線圈電流:167 mA 切換電壓:400 V 安裝風格:Chassis 觸點材料:
FTR-JRJB018W 功能描述:通用繼電器 POWER RoHS:否 制造商:Omron Electronics 觸點形式:1 Form A (SPST-NO) 觸點電流額定值:150 A 線圈電壓:24 VDC 線圈電阻:144 Ohms 線圈電流:167 mA 切換電壓:400 V 安裝風格:Chassis 觸點材料:
發布緊急采購，3分鐘左右您將得到回復。

采購需求

(若只采購一條型號，填寫一行即可)

發布成功！您可以繼續發布采購。也可以進入我的后臺，查看報價

發布成功！您可以繼續發布采購。也可以進入我的后臺，查看報價

*型號 *數量 廠商 批號 封裝
添加更多采購

我的聯系方式

*
*
*