- 您現在的位置：買賣IC網 > PDF目錄382970 > FT245BM (Electronic Theatre Controls, Inc.) FT245BM USB FIFO ( USB - Parallel ) I.C. PDF資料下載
參數資料
| 型號： | FT245BM |
| 廠商： | Electronic Theatre Controls, Inc. |
| 英文描述： | FT245BM USB FIFO ( USB - Parallel ) I.C. |
| 中文描述： | FT245BM的USB先進先出（USB端口-并行）集成電路 |
| 文件頁數： | 9/24頁 |
| 文件大?。?/td> | 505K |
| 代理商： | FT245BM |
DS245BL Version 1.6 Future Technology Devices Intl. Ltd. 2005
Page 9 of 24
FT245BL USB FIFO ( USB - Parallel ) I.C.
POWER CONTROL GROUP
Pin#
Signal
10
PWREN#
Type
OUT
Description
Goes Low after the device is configured via USB, then high during USB suspend.
Can be used to control power to external logic using a P-Channel Logic Level
MOSFET switch. Enable the Interface Pull-Down Option in EEPROM when using
the PWREN# pin in this way.
The Send Immediate / WakeUp signal combines two functions on a single pin. If
USB is in suspend mode (PWREN# = 1) and remote wakeup is enabled in the
EEPROM , strobing this pin low will cause the device to request a resume on the
USB Bus. Normally, this can be used to wake up the Host PC.
During normal operation (PWREN# = 0), if this pin is strobed low any data in the
device TX buffer will be sent out over USB on the next Bulk-IN request from the
drivers regardless of the pending packet size. This can be used to optimise USB
transfer speed for some applications. Tie this pin to VCCIO if not used.
11
SI / WU
IN
MISCELLANEOUS SIGNAL GROUP
Pin#
Signal
4
RESET#
Type
IN
Description
Can be used by an external device to reset the FT245BL. If not required, tie to
VCC.
Output of the internal Reset Generator. Stays high impedance for ~ 5ms after
VCC > 3.5V and the internal clock starts up, then clamps its output to the 3.3V
output of the internal regulator. Taking RESET# low will also force RSTOUT# to
drive low. RSTOUT# is NOT affected by a USB Bus Reset.
Input to 6MHz Crystal Oscillator Cell. This pin can also be driven by an external
6MHz clock if required. Note : Switching threshold of this pin is VCC/2, so if
driving from an external source, the source must be driving at 5V CMOS level or
a.c. coupled to centre around VCC/2.
Output from 6MHz Crystal Oscillator Cell. XTOUT stops oscillating during USB
suspend, so take care if using this signal to clock external logic.
Puts device in I.C. test mode – must be tied to GND for normal operation.
5
RSTOUT#
OUT
27
XTIN
IN
28
XTOUT
OUT
31
TEST
IN
相關PDF資料 |
PDF描述 |
|---|---|
| FT245BQ | FT245BQ USB FIFO ( USB - Parallel ) I.C. |
| FT6116 | 2K X 8 CMOS SRAM |
| FT8U100AX | FT8U100AX USB Compound Hub Controller |
| FTD1011 | Ultrahigh-Speed Switching Applications |
| FTD1012 | Load Switching Applications |
相關代理商/技術參數 |
參數描述 |
|---|---|
| FT245BM-TRAY | 功能描述:USB 接口集成電路 Obsolete See FT245RL RoHS:否 制造商:Cypress Semiconductor 產品:USB 2.0 數據速率: 接口類型:SPI 工作電源電壓:3.15 V to 3.45 V 工作電源電流: 最大工作溫度:+ 85 C 安裝風格:SMD/SMT 封裝 / 箱體:WLCSP-20 |
| FT245BQ | 制造商:未知廠家 制造商全稱:未知廠家 功能描述:FT245BQ USB FIFO ( USB - Parallel ) I.C. |
| FT245BQ-REEL | 功能描述:USB 接口集成電路 USB to Parallel FIFO IC QFN-32 RoHS:否 制造商:Cypress Semiconductor 產品:USB 2.0 數據速率: 接口類型:SPI 工作電源電壓:3.15 V to 3.45 V 工作電源電流: 最大工作溫度:+ 85 C 安裝風格:SMD/SMT 封裝 / 箱體:WLCSP-20 |
| FT245R | 制造商:FTDI 制造商全稱:FTDI 功能描述:USB FIFO I.C. Incorporating FTDIChip-ID⑩ Security Dongle |
| FT245R_10 | 制造商:FTDI 制造商全稱:FTDI 功能描述:USB FIFO IC - Single chip USB to parallel FIFO bidirectional data transfer interface |
發布緊急采購，3分鐘左右您將得到回復。