- 您現在的位置：買賣IC網 > PDF目錄223808 > FT245BL (Future Technology Devices International Ltd) PDF資料下載
參數資料
| 型號： | FT245BL |
| 廠商： | Future Technology Devices International Ltd |
| 元件分類： | 微控制器/微處理器 |
| 中文描述： | SPECIALTY MICROPROCESSOR CIRCUIT, PQFP32 |
| 封裝： | 7 X 7 MM, 0.80 MM PITCH, LEAD FREE, LQFP-32 |
| 文件頁數： | 2/24頁 |
| 文件大小： | 995K |
| 代理商： | FT245BL |
DS245B Version 1.7
Future Technology Devices Intl. Ltd. 2005
Page 10 of 24
FT245BM USB FIFO ( USB - Parallel ) I.C.
POWER AND GND GROUP
Pin#
Signal
Type
Description
6
3V3OUT
OUT
3.3 volt Output from the integrated L.D.O. regulator This pin should be decoupled
to GND using a 33nF ceramic capacitor in close proximity to the device pin. Its
prime purpose is to provide the internal 3.3V supply to the USB transceiver cell
and the RSTOUT# pin. A small amount of current (<= 5mA) can be drawn from
this pin to power external 3.3V logic if required.
3,26
VCC
PWR
+4.35 volt to +5.25 volt VCC to the device core, LDO and none-FIFO interface
pins.
13
VCCIO
PWR
+3.0 volt to +5.25 volt VCC to the FIFO interface pins 10..12, 14..16 and 18..25.
When interfacing with 3.3V external logic in a bus powered design connect
VCCIO to a 3.3V supply generated from the USB bus. When interfacing with
3.3V external logic in a self powered design connect VCCIO to the 3.3V supply
of the external logic. Otherwise connect to VCC to drive out at 5V CMOS level.
9,17
GND
PWR
Device - Ground Supply Pins
30
AVCC
PWR
Device - Analog Power Supply for the internal x8 clock multiplier
29
AGND
PWR
Device - Analog Ground Supply for the internal x8 clock multiplier
Note 1 : In Input Mode, these pins are pulled to VCCIO via internal 200K resistors. These can be programmed to
gently pull low during USB suspend ( PWREN# = “1” ) by setting this option in the EEPROM.
Note 2: During device reset, these pins are tri-state but pulled up to VCCIO via internal 200K resistors.
Note 3: During device reset, these pins are tri-state but pulled up to VCC via internal 200K resistors.
OBSOLETE
相關PDF資料 |
PDF描述 |
|---|---|
| FT245BQ | |
| FT245BM | |
| FTL-1419-3D | FIBER OPTIC TRANSCEIVER, 1290-1340nm, 1250Mbps(Tx), 1250Mbps(Rx), PANEL MOUNT |
| FTLF1321P1BTL | FIBER OPTIC TRANSCEIVER, 1270-1360nm, 2667Mbps(Tx), 2667Mbps(Rx), SURFACE MOUNT, LC CONNECTOR |
| FTLF1321P1WTL | FIBER OPTIC TRANSCEIVER, 1270-1360nm, 2667Mbps(Tx), 2667Mbps(Rx), SURFACE MOUNT, LC CONNECTOR |
相關代理商/技術參數 |
參數描述 |
|---|---|
| FT245BL/TR | 制造商:Future Technology Devices International (FTDI Chip) 功能描述:IC USB FIFO SMD LQFP32 245 制造商:Future Technology Devices International (FTDI Chip) 功能描述:IC, USB FIFO, SMD, LQFP32, 245 制造商:Future Technology Devices International (FTDI Chip) 功能描述:IC, USB FIFO INTERFACE, 480MBPS, LQFP-32; USB Type:FIFO; USB Version:1.1, 2.0; Supply Voltage Min:4.35V; Supply Voltage Max:5.25V; Digital IC Case Style:LQFP; No. of Pins:32; Data Rate:480Mbps; No. of Ports:2; MSL:MSL 3 - 168 hours ;RoHS Compliant: Yes |
| FT245BL-REEL | 功能描述:USB 接口集成電路 USB to Parallel FIFO IC LQFP-32 RoHS:否 制造商:Cypress Semiconductor 產品:USB 2.0 數據速率: 接口類型:SPI 工作電源電壓:3.15 V to 3.45 V 工作電源電流: 最大工作溫度:+ 85 C 安裝風格:SMD/SMT 封裝 / 箱體:WLCSP-20 |
| FT245BL-TRAY | 制造商:Future Technology Devices International (FTDI Chip) 功能描述:USB FIFO ( USB - PARALLEL ) I.C. |
| FT245BM | 功能描述:先進先出 Obsolete See FT245RL RoHS:否 制造商:IDT 電路數量: 數據總線寬度:18 bit 總線定向:Unidirectional 存儲容量:4 Mbit 定時類型:Synchronous 組織:256 K x 18 最大時鐘頻率:100 MHz 訪問時間:10 ns 電源電壓-最大:3.6 V 電源電壓-最小:6 V 最大工作電流:35 mA 最大工作溫度:+ 85 C 封裝 / 箱體:TQFP-80 封裝: |
| FT245BM-TRAY | 功能描述:USB 接口集成電路 Obsolete See FT245RL RoHS:否 制造商:Cypress Semiconductor 產品:USB 2.0 數據速率: 接口類型:SPI 工作電源電壓:3.15 V to 3.45 V 工作電源電流: 最大工作溫度:+ 85 C 安裝風格:SMD/SMT 封裝 / 箱體:WLCSP-20 |
發布緊急采購，3分鐘左右您將得到回復。