/BQ USB UAR" />
參數資料
型號： FT232BQ-REEL
廠商： FTDI, Future Technology Devices International Ltd
文件頁數： 10/34頁
文件大小： 0K
描述： IC NEW DESIGNS REFER TO FT232RQ
標準包裝： 1
系列： USBmadeEZ-UART
通道數： 1，UART
FIFO's： 256 字節
規程： RS232，RS422，RS485
電源電壓： 4.35 V ~ 5.25 V
帶自動流量控制功能： 是
帶調制解調器控制功能： 是
帶CMOS： 是
安裝類型： 表面貼裝
封裝/外殼： 32-WFQFN 裸露焊盤
供應商設備封裝： 32-QFN 裸露焊盤（5x5）
包裝： 標準包裝
其它名稱： 768-1067-6
Copyright 2011 Future Technology Devices International Limited
18
Document No.: FT_000329
FT232BL
/BQ USB UART IC Datasheet Version 2.2
Clearance No.: FTDI#
171
6.2 Self Powered Configuration
Figure 6.2 Self Powered Configuration
Figure 6.2 illustrates a typical USB self powered configuration. A USB Self Powered device gets its power
from its own POWER SUPPLY and does not draw current from the USB bus. The basic rules for USB Self
power devices are as follows:
a) A Self-Powered device should not force current down the USB bus when the USB Host or Hub
Controller is powered down.
b) A Self Powered Device can take as much current as it requires during normal operation and USB
suspend as it has its own POWER SUPPLY.
c) A Self Powered Device can be used with any USB Host and both Bus and Self Powered USB Hubs
PWRCTL (pin 14) is pulled high to configure the device with a USB Bus Power descriptor. The power
descriptor in the EEPROM should be programmed to a value of zero. The USB power descriptor option in
the EEPROM should be programmed to a value of zero (self powered).
To meet requirement, the 1.5 K pull-up resistors on USBDP is connected to RSTOUT# as per the bus-
power circuit. However, the USB Bus Power is used to control the RESET# Pin of the FT232B device.
When the USB Host or Hub is powered up RSTOUT# will pull the 1.5K resistor on USBDP to 3.3V, thus
identifying the device as a full speed device to USB. When the USB Host or Hub power is off, RESET# will
go low and the device will be held in reset. As RESET# is low, RSTOUT# will also be low, so no current
will be forced down USBDP via the 1.5K pull-up resistor when the host or hub is powered down. Failure to
do this may cause some USB host or hub controllers to power up erratically.
Note: When the FT232B is in reset, the UART interface pins all go tri-state. These pins have internal 200K
pull-up resistors to VCCIO, so they will gently pull high unless driven by some external logic.
相關PDF資料
PDF描述
ATMEGA168P-20MUR MCU AVR 16K FLASH 20MHZ 32-QFN
SC16IS740IPW,112 IC UART SINGLE W/FIFO 16-TSSOP
ATMEGA88-15AT MCU AVR 8K FLASH 15MHZ 32-TQFP
ATMEGA88V-15AT MCU AVR 8K FLASH 15MHZ 32-TQFP
ATMEGA88-15AT1 MCU AVR 8K FLASH 15MHZ 32-TQFP
相關代理商/技術參數
參數描述
FT232HL 制造商:FTDI 制造商全稱:FTDI 功能描述:FT232H Single Channel Hi-Speed USB to Multipurpose UART/FIFO IC
FT232HL-REEL 功能描述:USB 接口集成電路 USB HS to UART/FIFO SPI/JTAG/I2C LQFP-48 RoHS:否 制造商:Cypress Semiconductor 產品:USB 2.0 數據速率: 接口類型:SPI 工作電源電壓:3.15 V to 3.45 V 工作電源電流: 最大工作溫度:+ 85 C 安裝風格:SMD/SMT 封裝 / 箱體:WLCSP-20
FT232HL-TRAY 功能描述:USB 接口集成電路 USB HS to UART/FIFO SPI/JTAG/I2C LQFP-48 RoHS:否 制造商:Cypress Semiconductor 產品:USB 2.0 數據速率: 接口類型:SPI 工作電源電壓:3.15 V to 3.45 V 工作電源電流: 最大工作溫度:+ 85 C 安裝風格:SMD/SMT 封裝 / 箱體:WLCSP-20
FT232HQ-REEL 功能描述:USB 接口集成電路 USB HS to UART/FIFO SPI/JTAG/I2C QFN-48 RoHS:否 制造商:Cypress Semiconductor 產品:USB 2.0 數據速率: 接口類型:SPI 工作電源電壓:3.15 V to 3.45 V 工作電源電流: 最大工作溫度:+ 85 C 安裝風格:SMD/SMT 封裝 / 箱體:WLCSP-20
FT232HQ-TRAY 功能描述:USB 接口集成電路 USB HS to UART/FIFO SPI/JTAG/I2C QFN-48 RoHS:否 制造商:Cypress Semiconductor 產品:USB 2.0 數據速率: 接口類型:SPI 工作電源電壓:3.15 V to 3.45 V 工作電源電流: 最大工作溫度:+ 85 C 安裝風格:SMD/SMT 封裝 / 箱體:WLCSP-20
發布緊急采購，3分鐘左右您將得到回復。

采購需求

(若只采購一條型號，填寫一行即可)

發布成功！您可以繼續發布采購。也可以進入我的后臺，查看報價

發布成功！您可以繼續發布采購。也可以進入我的后臺，查看報價

*型號 *數量 廠商 批號 封裝
添加更多采購

我的聯系方式

*
*
*