參數資料
型號: FT2232HQ-REEL
廠商: FTDI, Future Technology Devices International Ltd
文件頁數: 25/67頁
文件大?。?/td> 0K
描述: IC USB HS DUAL UART/FIFO 64-QFN
標準包裝: 1
系列: USBmadeEZ-FIFO,F(xiàn)T-X,X-Chip
特點: USB 至 UART 和(或)FIFO、SPI、I2C、JTAG
通道數: 2,DUART
FIFO's: 4096 字節
規程: RS232,RS422,RS485
電源電壓: 3 V ~ 3.6 V
帶并行端口:
帶自動流量控制功能:
帶調制解調器控制功能:
帶CMOS:
安裝類型: 表面貼裝
封裝/外殼: 64-VFQFN 裸露焊盤
供應商設備封裝: 64-QFN
包裝: 標準包裝
產品目錄頁面: 634 (CN2011-ZH PDF)
其它名稱: 768-1025-6
Copyright 2012 Future Technology Devices International Limited
31
Document No.: FT_000061
FT2232H DUAL HIGH SPEED USB TO MULTIPURPOSE UART/FIFO IC
Version 2.21
Clearance No.: FTDI#77
4.6 MPSSE Interface Mode Description.
MPSSE Mode is designed to allow the FT2232H to interface efficiently with synchronous serial protocols
such as JTAG, I2C and SPI Bus. It can also be used to program SRAM based FPGAs over USB. The
MPSSE interface is designed to be flexible so that it can be configured to allow any synchronous serial
protocol (industry standard or proprietary) to be implemented using the FT2232H. MPSSE is available on
channel A and channel B.
MPSSE is fully configurable, and is programmed by sending commands down the data stream. These can
be sent individually or more efficiently in packets. MPSSE is capable of a maximum sustained data rate of
30 Mbits/s.
When a channel is configured in MPSSE mode, the IO timing and signals used are shown in Figure 4.7
and Table 4.3 These show timings for CLKOUT=30MHz. CLKOUT can be divided internally to be provide a
slower clock.
Figure 4.7 MPSSE Signal Waveforms
Name
Minimum
Typical
Maximum
Units
Description
t1
33.33
ns
CLKOUT period
t2
15
16.67
ns
CLKOUT high period
t3
15
16.67
ns
CLKOUT low period
t4
1
7.15
ns
CLKOUT to TDI/DO delay
t5
0
ns
TDO/DI hold time
t6
11
TDO/DI setup time
Table 4.3 MPSSE Signal Timings
MPSSE mode is enabled using Set Bit Bang Mode driver command. A hex value of 2 will enable it, and a
hex value of 0 will reset the device. See application note AN2232L-02, “Bit Mode Functions for the
FT2232D” for more details and examples.
The MPSSE command set is fully described in application note AN_108 – “Command Processor For
MPSSE and MCU Host Bus Emulation Modes”.
The following additional application notes are available for configuring the MPSSE :
AN_109 – “Programming Guide for High Speed FTCI2C DLL”
AN_110 – “Programming Guide for High Speed FTCJTAG DLL”
AN_111 – “Programming Guide for High Speed FTCSPI DLL”
相關PDF資料
PDF描述
FT232BL-REEL IC USB FS SERIAL UART 32-LQFP
FT232HL-REEL IC HS USB TO UART/FIFO 48LQFP
FT232RL-REEL IC USB FS SERIAL UART 28-SSOP
FT245BL-REEL IC USB FS PARALLEL FIFO 32-LQFP
FT245RL-REEL IC USB TO PARALLEL FIFO 28-SSOP
相關代理商/技術參數
參數描述
FT2232HQ-TRAY 功能描述:USB 接口集成電路 USB HS to Dual UART/ FIFO/SPI/JTAG/I2C RoHS:否 制造商:Cypress Semiconductor 產品:USB 2.0 數據速率: 接口類型:SPI 工作電源電壓:3.15 V to 3.45 V 工作電源電流: 最大工作溫度:+ 85 C 安裝風格:SMD/SMT 封裝 / 箱體:WLCSP-20
FT2232L 功能描述:UART 接口集成電路 Obsolete See FT2232D-REEL RoHS:否 制造商:Texas Instruments 通道數量:2 數據速率:3 Mbps 電源電壓-最大:3.6 V 電源電壓-最小:2.7 V 電源電流:20 mA 最大工作溫度:+ 85 C 最小工作溫度:- 40 C 封裝 / 箱體:LQFP-48 封裝:Reel
FT2232L/TR 制造商:Future Technology Devices International (FTDI Chip) 功能描述:USB UART/FIFO SMD 2232 LQFP48
FT22L 功能描述:OVEN FOOD PROBE RoHS:是 類別:測試設備 >> 測試引線 - 熱電偶,溫度探頭 系列:FT 標準包裝:1 系列:6543 類型:J 型熱電偶 使用:液體,半固體 尖端 - 類型:防浸漬 / 穿透式,圓頭 插頭類型:超微型(熱電偶插頭) 探針溫度范圍:-40 ~ 2000°F(-40 ~ 1093°C) 線纜長度:- 線纜絕緣:- 插頭顏色:黑 探針長度:12.000"(304.80mm) 探針材料:-
FT230A 制造商:Black Box Corporation 功能描述:HAND STRIPPER