參數資料
型號： FT2232HL-TRAY
廠商： FTDI, Future Technology Devices International Ltd
文件頁數： 7/67頁
文件大?。?/td> 0K
描述： IC USB HS DUAL UART/FIFO 64-LQFP
標準包裝： 160
系列： USBmadeEZ-FIFO，F(xiàn)T-X，X-Chip
特點： USB 至 UART 和（或）FIFO、SPI、I2C、JTAG
通道數： 2，DUART
FIFO's： 4096 字節
規程： RS232，RS422，RS485
電源電壓： 3 V ~ 3.6 V
帶并行端口： 是
帶自動流量控制功能： 是
帶調制解調器控制功能： 是
帶CMOS： 是
安裝類型： 表面貼裝
封裝/外殼： 64-LQFP
供應商設備封裝： 64-LQFP
包裝： 托盤
其它名稱： FT2232HL - TRAY
Copyright 2012 Future Technology Devices International Limited
15
Document No.: FT_000061
FT2232H DUAL HIGH SPEED USB TO MULTIPURPOSE UART/FIFO IC
Version 2.21
Clearance No.: FTDI#77
3.4.4 FT2232H pins used in a Synchronous or Asynchronous Bit-Bang
Interface
The FT2232H channel A or channel B can be configured as a synchronous or asynchronous bit-bang
interface. Bit-bang mode is a special FTDI FT2232H device mode that changes the 8 IO lines on either (or
both) channels into an 8 bit bi-directional data bus. There are two types of bit-bang modes: synchronous
and asynchronous.
When configured in any bit-bang mode, the pins used and the descriptions of the signals are shown in
Channel A
Pin No.
Channel B
Pin No.
Name
Type
Configuration Description
24,23,22,21
,
19,18,17,16
46,45,44,43,
41,40,39,38
Channel A =
ADBUS[7:0]
Channel B =
BDBUS[7:0]
I/O
D7 to D0 bidirectional Bit-Bang parallel I/O
data pins
27
52
WRSTB#
OUTPUT
Write strobe, active low output indicates
when new data has been written to the I/O
pins from the Host PC (via the USB
interface).
28
53
RDSTB#
OUTPUT
Read strobe, this output rising edge
indicates when data has been read from the
parallel I/O pins and sent to the Host PC
(via the USB interface).
30
55
SIWU
INPUT
The Send Immediate / WakeUp signal
combines two functions on a single pin. If
USB is in suspend mode (PWREN# = 1) and
remote wakeup is enabled in the EEPROM ,
strobing this pin low will cause the device to
request a resume on the USB Bus.
Normally, this can be used to wake up the
Host PC.
During normal operation (PWREN# = 0), if
this pin is strobed low any data in the device
TX buffer will be sent out over USB on the
next Bulk-IN request from the drivers
regardless of the pending packet size. This
can be used to optimize USB transfer speed
for some applications. Tie this pin to VCCIO
if not used. (Also see note 1, 2, 3 in section
Table 3.7 Channel A and Channel B Synchronous or Asynchronous Bit-Bang Configured Pin Descriptions
For a functional description of this mode, please refer to section 4.10 Synchronous and Asynchronous Bit-
相關PDF資料
PDF描述
SC28L92A1A,512 IC UART DUAL W/FIFO 44-PLCC
VI-B5B-IY CONVERTER MOD DC/DC 95V 50W
D38999/20WD19PC CONN RCPT 19POS WALL MNT W/PINS
ATMEGA169PV-8MCHR MCU AVR 16KB FLASH 16MHZ 64QFN
MS27484T16B8PA CONN PLUG 8POS STRAIGHT W/PINS
相關代理商/技術參數
參數描述
FT2232HMINIMODULE 制造商:Future Technology Devices International (FTDI Chip) 功能描述:USB Hi-Speed FT2232H Evaluation Module 制造商:Future Technology Devices International (FTDI Chip) 功能描述:USB to serial/FIFO development module
FT2232H-MINI-MODULE 制造商:Future Technology Devices International (FTDI Chip) 功能描述:IC,EVALUATION MODULE;FT2232H;USB HI-SPEED
FT2232HQ 制造商:Future Technology Devices International (FTDI Chip) 功能描述:USB Hi-Speed to Dual Channel Serial UART/FIFO/JTAG/SPI/I2C IC - QFN-64
FT2232HQ_MINI_ MODULE 功能描述:界面開發工具 USB Hi-Speed FT2232H Evaluation Module RoHS:否 制造商:Bourns 產品:Evaluation Boards 類型:RS-485 工具用于評估:ADM3485E 接口類型:RS-485 工作電源電壓:3.3 V
FT2232HQ-4000 制造商:FTDI 制造商全稱:FTDI 功能描述:DUAL HIGH SPEED USB TO MULTIPURPOSE UART/FIFO IC
發布緊急采購，3分鐘左右您將得到回復。

采購需求

(若只采購一條型號，填寫一行即可)

發布成功！您可以繼續發布采購。也可以進入我的后臺，查看報價

發布成功！您可以繼續發布采購。也可以進入我的后臺，查看報價

*型號 *數量 廠商 批號 封裝
添加更多采購

我的聯系方式

*
*
*