- 您現在的位置：買賣IC網 > PDF目錄44770 > FS2540-9PDD (POWER-ONE INC) 2-OUTPUT DC-DC REG PWR SUPPLY MODULE PDF資料下載
參數資料
| 型號： | FS2540-9PDD |
| 廠商： | POWER-ONE INC |
| 元件分類： | 電源模塊 |
| 英文描述： | 2-OUTPUT DC-DC REG PWR SUPPLY MODULE |
| 封裝： | HEAT SINK, METAL, CASE S02, MODULE |
| 文件頁數： | 18/33頁 |
| 文件大?。?/td> | 438K |
| 代理商： | FS2540-9PDD |
第1頁第2頁第3頁第4頁第5頁第6頁第7頁第8頁第9頁第10頁第11頁第12頁第13頁第14頁第15頁第16頁第17頁當前第18頁第19頁第20頁第21頁第22頁第23頁第24頁第25頁第26頁第27頁第28頁第29頁第30頁第31頁第32頁第33頁
S Series Data Sheet
100 Watt AC-DC and DC-DC Converters
APR 26, 2006 revised to SEP 25, 2006
Page 25 of 33
www.power-one.com
Load
1
2
S+
Vo+
Vo–
S–
Vi+
Vi–
T
Vi+
Vi–
S+
Vo+
Vo–
S–
T
1
Max. 5 converters in parallel connection
11036_012006
Converter
Fig. 29
Paralleling of single-output models using option T with the
sense lines connected at the load
1 Leads should have equal length and cross sections and should
run in the same cable loom.
2 Diodes for redundant operation.
Vo+
Vo–
Vo+
Vo–
Load
Vo+
Vo–
11003_102005
Fig. 28
An example of poor wiring for connections in parallel
(unequal length of load lines)
Option T: Current Sharing
This option ensures that the output currents are
approximately shared between all paralleled converters,
hence increasing system reliability. To use this facility,
simply interconnect the T pins of all converters and make
sure that the reference pins for the T-pin (S- for the S1000
or Vo1– for S2000) are also connected together. The load
lines should have equal length and cross section to ensure
equal voltage drops. Not more than 5 converters should be
connected in parallel. The R-pins should be left in an open-
circuit condition. If not, prior to paralleling the Vo1 outputs
should be individually adjusted within 1 to 2%. Parallel
connection
of
converters
with
option
P
is
not
recommended.
Option P: Potentiometer
The potentiometer allows for an output voltage adjustment
in the range of +10/–60% of Vo nom. It is accessible
through a hole in the front cover. This feature enables
compensation of voltage drops across the connector and
wiring. Option P is not recommended if models are
connected in parallel.
In double-output models both outputs are influenced by the
potentiometer setting. If option P is fitted, the R-pin 16 is
not connected.
Note: If the output voltage is increased above Vo nom via the
R-input control, option P setting, remote sensing, or option T,
the output current(s) should be reduced accordingly so that
Po nom is not exceeded.
Load
Max. 5 converters in parallel connection
+–
Power bus
Vo2–
Vo2+
Vo1–
Vo1+
T
Vo2–
Vo2+
Vo1–
Vo1+
T
Converter
11037_012006
Fig. 30
Paralleling of double output models with the outputs
connected in series, and using option T in an application
with a power bus. Note that the signal at the T-pins is
referenced to Vo1-.
相關PDF資料 |
PDF描述 |
|---|---|
| FS2660-7EPDD | 2-OUTPUT DC-DC REG PWR SUPPLY MODULE |
| FS2660-7ERD1 | 2-OUTPUT DC-DC REG PWR SUPPLY MODULE |
| FS2660-7P | 2-OUTPUT DC-DC REG PWR SUPPLY MODULE |
| FS2660-9ERD8T | 2-OUTPUT DC-DC REG PWR SUPPLY MODULE |
| FS2660-9RD8 | 2-OUTPUT DC-DC REG PWR SUPPLY MODULE |
相關代理商/技術參數 |
參數描述 |
|---|---|
| FS25R06KF | 制造商:未知廠家 制造商全稱:未知廠家 功能描述:TRANSISTOR | IGBT POWER MODULE | 3-PH BRIDGE | 600V V(BR)CES | 25A I(C) |
| FS25R06KF2 | 制造商:未知廠家 制造商全稱:未知廠家 功能描述:TRANSISTOR | IGBT POWER MODULE | 3-PH BRIDGE | 600V V(BR)CES | 25A I(C) |
| FS25R10KF2 | 制造商:未知廠家 制造商全稱:未知廠家 功能描述:TRANSISTOR | IGBT POWER MODULE | 3-PH BRIDGE | 1KV V(BR)CES | 25A I(C) |
| FS25R12KE3G | 功能描述:IGBT 模塊 N-CH 1.2KV 40A RoHS:否 制造商:Infineon Technologies 產品:IGBT Silicon Modules 配置:Dual 集電極—發射極最大電壓 VCEO:600 V 集電極—射極飽和電壓:1.95 V 在25 C的連續集電極電流:230 A 柵極—射極漏泄電流:400 nA 功率耗散:445 W 最大工作溫度:+ 125 C 封裝 / 箱體:34MM 封裝: |
| FS25R12KF | 制造商:未知廠家 制造商全稱:未知廠家 功能描述:TRANSISTOR | IGBT POWER MODULE | 3-PH BRIDGE | 1.2KV V(BR)CES | 25A I(C) |
發布緊急采購，3分鐘左右您將得到回復。