- 您現在的位置：買賣IC網 > PDF目錄370215 > FP80 Filter & Ring Core Chokes PDF資料下載
參數資料
| 型號： | FP80 |
| 英文描述： | Filter & Ring Core Chokes |
| 中文描述： | 過濾器 |
| 文件頁數： | 2/5頁 |
| 文件大?。?/td> | 119K |
| 代理商： | FP80 |
Accessories
Filter & Ring Core Chokes FP L and LP Series
REV. SEP 29, 2003
Page 2 of 5
Electrical Data Filter Blocks
General Condition: T
A
= 25°C unless otherwise specified
Table 2: Filter blocks FP
Characteristics
Conditions
FP38
typ
FP80
typ
FP144
typ
min
max
min
max
min
max
Unit
I
Fn
Rated current
L= 0.75 L
o
4
4
2
A DC
U
Fn
Rated voltage
T
C min
...T
C max
5
40
5
80
15
144
V DC
R
F
Ohmic resistance
18
20
22
18
20
22
90
95
100
my
L
o
No load inductance
I
L
= 0, T
C min
...T
C max
30
34
38
30
34
38
88
100
112
μH
T
A
Ambient temperature
I
F
= I
Fn
–40
80
–40
80
–40
95
°C
T
C
Case temperature
–40
92
–40
92
–40
98
T
S
Storage temperature
–40
100
–40
100
–55
100
For currents I
F
>
4 A the following derating takes place: T
A max
= 100 – 1.3 I
F2
[°C], T
C max
= 100 – 0.49 I
F2
[°C]
Reduction of Output Ripple
Even though switching regulators have an inherently low
output ripple, certain sensitive applications need even fur-
ther reduction. In such cases, the filters designed to reduce
disturbances at the input, can also be used for reducing the
ripple on the output voltage (even better results with regard
to the ripple and dynamic control deviation can be achieved
by using low-loss ring core chokes in combination with an
external capacitor, see below).
The output ripple can be reduced by the use of filter blocks
by about 24 dB. The formula for the ripple u
R
at the load R
L
is as follows:
u
R
= 0.063 u
o
(Ripple voltage u
o
is given for specific regulators in the cor-
responding data section).
Consider, that the filter not only affects the output ripple but
can also influence the voltage across the load R
L
in the
event of load changes. The static load regulation increases
with the ohmic resistance of the choke i.e. 24 mV/A for the
FP 38 and FP 80 filters and 95 mV/A for the FP 144 filter.
Vi+
Gi–
Vo+
Go–
PSR
R
L
U
R
U
Filter
Uio
Uii
Gi
U
o
12010
Fig. 2
Reduction of voltage interference by FP filters
Input Interference Reduction
An AC ripple current can be measured at the input of any
switching regulator, even if they are equipped with an input
filter. Depending on the types of filters used, common and/
or differential mode interferences can be reduced. They will
also help to further increase the surge and burst immunity
of the power supplies.
The FP filters considerably increase the source impedance
of the regulators superimposed interference, to a value
which is normally high in comparison to the impedance of
the source (Z
Line
). The interference currents are therefore
practically independent of their source impedance. The fil-
ter will reduce these currents by approximately 25 dB at a
frequency of 150 kHz.
The interference voltages at the filter input are due to the
remaining interference currents flowing through the source
impedance. The resulting interference voltage reduction
can be seen in the following figure. For frequencies above
the regulator switching frequency the attenuation will in-
crease (up to 2 MHz approx.).
Parallel operation: When several switching regulator inputs
are connected in parallel, each regulator should be
equipped with a separate input filter. Interconnections
should only be made in front of the filter or at its input Uii
(i. e. the central ground point should be before or at the filter
and under no circumstances at the regulator input).
0
1
2
3
4
5
6
10
20
30
40
Z
Line
[ ]
Source impedance
0
I
Att. [dB]
inductive
resistive
capacitive
12009
Fig. 1
Interference voltage reduction with FP filters at f = 150 kHz
相關PDF資料 |
PDF描述 |
|---|---|
| FP210-D-250-22 | ?Differential Magnetoresistive Sensor? |
| FP210-L-100-22 | ?Differential Magnetoresistive Sensor? |
| FP210 | NPN Epitaxial Planar Silicon Transistor Driver Applications |
| FP210L100-22 | Differential Magnetoresistive Sensor |
| FP210D250-22 | Differential Magnetoresistive Sensor |
相關代理商/技術參數 |
參數描述 |
|---|---|
| FP80 | 制造商:ebm-papst Inc 功能描述:FILTERS 80MM PK5 |
| FP801 | 制造商:DAESAN 制造商全稱:Daesan Electronics Corp. 功能描述:CURRENT 8.0 Amperes VOLTAGE 50 to 1000 Volts |
| FP8015-V19 | 制造商:HENKEL 功能描述:3549 - REWORKABLE UNDERFILL - 30ML - IDH# 910487 |
| FP802 | 制造商:DAESAN 制造商全稱:Daesan Electronics Corp. 功能描述:CURRENT 8.0 Amperes VOLTAGE 50 to 1000 Volts |
| FP803 | 制造商:DAESAN 制造商全稱:Daesan Electronics Corp. 功能描述:CURRENT 8.0 Amperes VOLTAGE 50 to 1000 Volts |
發布緊急采購，3分鐘左右您將得到回復。