- 您現在的位置：買賣IC網 > PDF目錄10555 > FMS6203MTC1400X (Fairchild Semiconductor)IC VIDEO DRIVER 3CH 0DB 14-TSSOP PDF資料下載
參數資料
| 型號： | FMS6203MTC1400X |
| 廠商： | Fairchild Semiconductor |
| 文件頁數： | 6/8頁 |
| 文件大?。?/td> | 0K |
| 描述： | IC VIDEO DRIVER 3CH 0DB 14-TSSOP |
| 標準包裝： | 1 |
| 類型： | 驅動器 |
| 應用： | 錄音機，機頂盒 |
| 安裝類型： | 表面貼裝 |
| 封裝/外殼： | 14-TSSOP（0.173"，4.40mm 寬） |
| 供應商設備封裝： | 14-TSSOP |
| 包裝： | 標準包裝 |
| 其它名稱： | FMS6203MTC1400XDKR |
2006 Fairchild Semiconductor Corporation
www.fairchildsemi.com
FMS6203 Rev. 1.0.4
6
FM
S6203
—
Low-
C
ost
,3-
C
h
annel,
Video
Filt
er
D
river
f
o
rSD
/PS/H
D
Layout Considerations
General layout and supply bypassing play a major role
in
high-frequency
performance
and
thermal
characteristics. Fairchild offers an evaluation board to
guide layout and aid device evaluation. The evaluation
board is a four-layer board with full power and ground
planes. Following this layout configuration provides
optimum performance and thermal characteristics for
the device. For the best results, follow the steps and
recommended routing rules listed below.
Recommended Routing / Layout Rules
Do not run analog and digital signals in parallel.
Use separate analog and digital power planes to
supply power.
Run traces on top of the ground plane at all times.
Do not run traces over ground/power splits.
Avoid routing at 90-degree angles.
Minimize clock and video data trace length
differences.
Include 10F and 0.1F ceramic power supply
bypass capacitors.
Place the 0.1F capacitor within 0.1 inches of the
device power pin.
Place the 10F capacitor within 0.75 inches of the
device power pin.
For multi-layer boards, use a large ground plane to
help dissipate heat.
For two-layer boards, use a ground plane that
extends beyond the device body by at least 0.5
inches on all sides. Include a metal paddle under
the device on the top layer.
Minimize all trace lengths to reduce series
inductance.
Thermal Considerations
Since the interior of most systems, such as set-top
boxes, TVs, and DVD players, are at +70C;
consideration must be given to providing an adequate
heat sink for the device package for maximum heat
dissipation. When designing a system board, determine
how much power each device dissipates. Ensure that
devices of high power are not placed in the same
location, such as directly above (top plane) and below
bottom plane) each other on the PCB.
PCB Thermal Layout Considerations
Understand the system power requirements and
environmental conditions.
Maximize thermal performance of the PCB.
Consider 70m copper for high-power designs.
Make the PCB as thin as possible by reducing FR4
thickness.
Use vias in the power pad to tie adjacent layers
together.
Remember that baseline temperature is a function
of board area, not copper thickness.
Use modeling techniques for first-order
approximation.
Output Considerations
The FMS6203 outputs are DC offset from the input by
150mV; therefore, VOUT = 2VIN DC+150mV. This offset
is required to obtain optimal performance from the
output driver and is held at the minimum value to
decrease the standing DC current into the load. Since
the FMS6203 has a 2x (6dB) gain, the output is typically
connected via a 75-series back-matching resistor
followed by the 75 video cable. Because of the
inherent divide by two of this configuration, the blanking
level at the load of the video signal is always less than
1V. When AC-coupling the output, ensure that the
coupling capacitor of choice passes the lowest
frequency content in the video signal and that line time
distortion (video tilt) is kept as low as possible.
The selection of the coupling capacitor is a function of
the subsequent circuit input impedance and the leakage
current of the input being driven. To obtain the highest
quality output video signal, the series termination
resistor must be placed as close to the device output
pin as possible. This greatly reduces the parasitic
capacitance and inductance effect on the FMS6203
output driver. Recommended distance from device pin
to place series termination resistor is no greater than
0.1 inches.
Figure 3.
Distance from Device Pin to Series
Termination Resistor
相關PDF資料 |
PDF描述 |
|---|---|
| MS3106A12S-4P | CONN PLUG 1POS STRAIGHT W/PINS |
| VI-JTJ-MW-F4 | CONVERTER MOD DC/DC 36V 100W |
| 97-3102A-12SL-844P | CONN RCPT 4POS BOX MNT W/PIN |
| EXP-0911/02/P | CONN PLUG 2POS IP68 W/PINS |
| VI-JTJ-MW-F3 | CONVERTER MOD DC/DC 36V 100W |
相關代理商/技術參數 |
參數描述 |
|---|---|
| FMS6203MTC1406 | 功能描述:視頻 IC SIGNAL_CONDITIONING RoHS:否 制造商:Fairchild Semiconductor 工作電源電壓:5 V 電源電流:80 mA 最大工作溫度:+ 85 C 封裝 / 箱體:TSSOP-28 封裝:Reel |
| FMS6203MTC1406X | 功能描述:視頻 IC LowCost 3-Chnl Video FltrDrvrs SD/PS/HD RoHS:否 制造商:Fairchild Semiconductor 工作電源電壓:5 V 電源電流:80 mA 最大工作溫度:+ 85 C 封裝 / 箱體:TSSOP-28 封裝:Reel |
| FMS6243 | 制造商:FAIRCHILD 制造商全稱:Fairchild Semiconductor 功能描述:Low-Cost, 3-Channel, SD Video Filter Drivers with External Delay Control |
| FMS6243A WAF | 制造商:Fairchild Semiconductor Corporation 功能描述: |
| FMS6243A WAF | 制造商:Fairchild Semiconductor Corporation 功能描述: |
發布緊急采購，3分鐘左右您將得到回復。