- 您現在的位置：買賣IC網 > PDF目錄375849 > FM3116-S (Electronic Theatre Controls, Inc.) Integrated Processor Companion with Memory PDF資料下載
參數資料
| 型號： | FM3116-S |
| 廠商： | Electronic Theatre Controls, Inc. |
| 英文描述： | Integrated Processor Companion with Memory |
| 中文描述： | 綜合處理器與記憶體伴侶 |
| 文件頁數： | 6/22頁 |
| 文件大?。?/td> | 286K |
| 代理商： | FM3116-S |
The comparator is a general purpose device and its
application is not limited to the NMI function.
The comparator is not integrated into the special
function registers except as it shares its output pin
with the CAL output. When the RTC calibration
mode is invoked by setting the CAL bit (register 00h,
bit 2), the CAL/PFO output pin will be driven with a
512 Hz square wave and the comparator will be
ignored. Since most users only invoke the calibration
mode during production, this should have no impact
on system operations using the comparator.
Note: The maximum voltage on the comparator input PFI
is limited to 3.75V under normal operating conditions.
Event Counter
The FM31xxx offers the user two battery-backed
event counters. Input pins CNT1 and CNT2 are
programmable edge detectors. Each clocks a 16-bit
counter. When an edge occurs, the counters will
increment their respective registers. Counter 1 is
located in registers 0Dh and 0Eh, Counter 2 is
located in registers 0Fh and 10h. These register
values can be read anytime VDD is above VTP, and
they will be incremented as long as a valid VBAK
power source is provided. To read, set the RC bit
register 0Ch bit 3 to 1. This takes a snapshot of all
four counter bytes allowing a stable value even if a
count occurs during the read. The registers can be
written by software allowing the counters to be
cleared or initialized by the system. Counts are
blocked during a write operation. The two counters
can be cascaded to create a single 32-bit counter by
setting the CC control bit (register 0Ch). When
cascaded, the CNT1 input will cause the counter to
increment. CNT2 is not used in this mode.
The control bits for event counting are located in
register 0Ch. Counter 1 Polarity is bit C1P, bit 0;
Counter 2 Polarity is C2P, bit 1; the Cascade Control
is CC, bit 2; and the Read Counter bit is RC bit 3.
C1P
FM3104/16/64/256
Rev 0.2
May 2003
Page 6 of 22
Figure 6. Event Counter
Serial Number
A memory location to write a 64-bit serial number is
provided. It is a writeable nonvolatile memory block
that can be locked by the user once the serial number
is set. The 8 bytes of data and the lock bit are all
accessed via the device ID for the processor
companion. Therefore the serial number area is
separate and distinct from the memory array. The
serial number registers can be written an unlimited
number of times, so these locations are general
purpose memory.
However once the lock bit is set the
values cannot be altered and the lock cannot be
removed.
Once locked the serial number registers can
still be read by the system.
The serial number is located in registers 11h to 18h.
The lock bit is SNL, register 0Bh bit 7. Setting the
SNL bit to a 1 disables writes to the serial number
registers, and
the SNL bit cannot be cleared
.
Real-Time Clock Operation
The real-time clock (RTC) is a timekeeping device
that can be battery or capacitor backed for
permanently-powered operation. It offers a software
calibration feature that allows high accuracy.
The RTC consists of an oscillator, clock divider, and
a register system for user access. It divides down the
32.768 kHz time-base and provides a minimum
resolution of seconds (1Hz). Static registers provide
the user with read/write access to the time values. It
includes registers for seconds, minutes, hours, day-
of-the-week, date, months, and years. A block
diagram (Figure 7) illustrates the RTC function.
The user registers are synchronized with the
timekeeper core using R and W bits in register 00h
described below. Changing the R bit from 0 to 1
transfers timekeeping information from the core into
holding registers that can be read by the user. If a
timekeeper update is pending when R is set, then the
core will be updated prior to loading the user
registers. The registers are frozen and will not be
updated again until the R bit is cleared to 0. R is used
for reading the time.
Setting the W bit to 1 locks the user registers.
Clearing it to 0 causes the values in the user registers
to be loaded into the timekeeper core. W is used for
writing new time values. Users should be certain not
to load invalid values, such as FFh, to the
timekeeping registers. Updates to the timekeeping
core occur continuously except when locked.
Backup Power
The real-time clock/calendar is intended to be
permanently powered. When the primary system
power fails, the voltage on the VDD pin will drop.
When VDD is less 2.5V the RTC (and event
counters) will switch to the backup power supply on
VBAK. The clock operates at extremely low current
in order to maximize battery or capacitor life.
16-bit Counter
CNT1
CC
CNT2
C2P
16-bit Counter
相關PDF資料 |
PDF描述 |
|---|---|
| FM31256-S | Integrated Processor Companion with Memory |
| FM3164-S | Integrated Processor Companion with Memory |
| FM3204 | Integrated Processor Companion with Memory |
| FM3204-G | Integrated Processor Companion with Memory |
| FM3204-S | Integrated Processor Companion with Memory |
相關代理商/技術參數 |
參數描述 |
|---|---|
| FM3116-STR | 功能描述:監控電路 16K w/RTC Pwr Mon WDT Bat Sw PF RoHS:否 制造商:STMicroelectronics 監測電壓數: 監測電壓: 欠電壓閾值: 過電壓閾值: 輸出類型:Active Low, Open Drain 人工復位:Resettable 監視器:No Watchdog 電池備用開關:No Backup 上電復位延遲（典型值）:10 s 電源電壓-最大:5.5 V 最大工作溫度:+ 85 C 安裝風格:SMD/SMT 封裝 / 箱體:UDFN-6 封裝:Reel |
| FM31256 | 制造商:RAMTRON 制造商全稱:RAMTRON 功能描述:Integrated Processor Companion with Memory |
| FM31256_11 | 制造商:RAMTRON 制造商全稱:RAMTRON 功能描述:Integrated Processor Companion with Memory |
| FM31256-G | 功能描述:監控電路 256K w/RTC Pwr Mon WDT Bat Sw PF RoHS:否 制造商:STMicroelectronics 監測電壓數: 監測電壓: 欠電壓閾值: 過電壓閾值: 輸出類型:Active Low, Open Drain 人工復位:Resettable 監視器:No Watchdog 電池備用開關:No Backup 上電復位延遲（典型值）:10 s 電源電壓-最大:5.5 V 最大工作溫度:+ 85 C 安裝風格:SMD/SMT 封裝 / 箱體:UDFN-6 封裝:Reel |
| FM31256-G | 制造商:Ramtron International Corporation 功能描述:Voltage Detector / Microprocessor Superv |
發布緊急采購，3分鐘左右您將得到回復。