- 您現在的位置：買賣IC網 > PDF目錄375845 > FM24C256 (Fairchild Semiconductor Corporation) 256K-Bit 2-Wire Bus Interface Serial EEPROM with Write Protect(帶寫保護的256K位的兩線控制總線接口串行EEPROM) PDF資料下載
參數資料
| 型號： | FM24C256 |
| 廠商： | Fairchild Semiconductor Corporation |
| 元件分類： | DRAM |
| 英文描述： | 256K-Bit 2-Wire Bus Interface Serial EEPROM with Write Protect(帶寫保護的256K位的兩線控制總線接口串行EEPROM) |
| 中文描述： | 256K位2線總線接口的串行EEPROM的寫入保護（帶寫保護的256K位的兩線控制總線接口串行EEPROM的） |
| 文件頁數： | 9/12頁 |
| 文件大?。?/td> | 89K |
| 代理商： | FM24C256 |
9
www.fairchildsemi.com
FM24C256 rev. B.3
F
Write Protection
Programming of the memory array will not take place if the WP pin
is connected to V
CC
. The device will accept control and word
addresses; but if the memory accessed is write protected by the
WP pin, the FM24C256xxx will not generate an acknowledge after
the first byte of data has been received, and thus the program
cycle will not be started when the stop condition is asserted.
Read Operation
Read operations are initiated in the same manner as write
operations, with the exception that the R/W bit of the slave address
is set to "1". There are three basic read operations: current
address read, random read and sequential read.
CURRENT ADDRESS READ
Internally the FM24C256xxx contains an address counter that
maintains the address of the last word accessed, incremented by
one. Therefore, if the last access (either a read or write) was to
address n, the next read operation would access data from
address n+1. Upon receipt of the slave address with R/W set to
"1," the FM24C256xxx issues an acknowledge and transmits the
eight bit word. The master will not acknowledge the transfer but
does generate a stop condition, and therefore discontinues trans-
mission. Refer to Figure 7for the sequence of address, acknowl-
edge and data transfer.
RANDOM READ
Random read operations allow the master to access any memory
location in a random manner. Prior to issuing the slave address
with the R/W bit set to "1", the master must first perform a "dummy"
write operation. The master issues a start condition, a slave
address, and then the word address to be read. After the word
address acknowledge, the master immediately reissues the start
condition and the slave address with the R/W bit set to "1". This will
be followed by an acknowledge from the FM24C256xxx and then
by the eight bit word. The master will not acknowledge the transfer
but does generate the stop condition, and therefore the
FM24C256xxx discontinues transmission. Refer to Figure 8 for
the address, acknowledge, and data transfer sequence.
SEQUENTIAL READ
Sequential reads can be initiated as either a current address read
or random access read. The first word is transmitted in the same
manner as the other read modes; however, the master now
responds with an acknowledge, indicating it requires additional
data. The FM24C256xxx continues to output data for each ac-
knowledge received. The read operation is terminated by the
master not responding with an acknowledge or by generating a
stop condition.
The data output is sequential, with the data from address n,
followed by the data n+1. The address counter for read operations
increments all word address bits, allowing the entire memory
contents to be serially read during one operation. After the entire
memory has been read, the counter "rolls over" and the
FM24C256xxx continues to output data for each acknowledge
received. Refer to Figure 9for the address, acknowledge, and
data transfer sequence.
S
T
O
P
A
C
K
A
C
K
Bus Activity:
Master
SDA Line
1 0 1 0
0
Bus Activity
A
C
K
DATA n
DATA n+63
A
C
K
WORD
ADDRESS (1)
WORD
ADDRESS (0)
SLAVE
ADDRESS
S
T
A
R
T
DS800023-9
Page Write (Figure 6)
相關PDF資料 |
PDF描述 |
|---|---|
| FM24C256LZEYYX | 256 KBit 2-Wire Bus Interface Serial EEPROM with Write Protect |
| FM24C256FLZEYYX | 256 KBit 2-Wire Bus Interface Serial EEPROM with Write Protect |
| FM24C256YYX | 256 KBit 2-Wire Bus Interface Serial EEPROM with Write Protect |
| FM24C256LYYX | 256 KBit 2-Wire Bus Interface Serial EEPROM with Write Protect |
| FM24C256FYYX | Shielded Paired Cable, EIA RS-232 and EIA RS-422; Number of Conductors:12; Conductor Size AWG:24; No. Strands x Strand Size:7 x 32; Jacket Material:Polyvinylchloride (PVC); Shielding Material:Aluminum Foil/Polyester Tape RoHS Compliant: Yes |
相關代理商/技術參數 |
參數描述 |
|---|---|
| FM24C256_05 | 制造商:RAMTRON 制造商全稱:RAMTRON 功能描述:256Kb FRAM Serial Memory |
| FM24C256B-G | 功能描述:F-RAM 256Kb Serial I2C 5V FRAM RoHS:否 存儲容量:512 Kbit 組織:64 K x 8 接口:SPI 工作電源電壓:2 V to 3.6 V 工作溫度范圍:- 40 C to + 85 C 安裝風格:SMD/SMT 封裝 / 箱體:SOIC-8 封裝:Tube 制造商:Cypress Semiconductor |
| FM24C256B-GTR | 功能描述:F-RAM 256Kb Serial I2C 5V FRAM RoHS:否 存儲容量:512 Kbit 組織:64 K x 8 接口:SPI 工作電源電壓:2 V to 3.6 V 工作溫度范圍:- 40 C to + 85 C 安裝風格:SMD/SMT 封裝 / 箱體:SOIC-8 封裝:Tube 制造商:Cypress Semiconductor |
| FM24C256EM8 | 功能描述:電可擦除可編程只讀存儲器 SOIC-8 RoHS:否 制造商:Atmel 存儲容量:2 Kbit 組織:256 B x 8 數據保留:100 yr 最大時鐘頻率:1000 KHz 最大工作電流:6 uA 工作電源電壓:1.7 V to 5.5 V 最大工作溫度:+ 85 C 安裝風格:SMD/SMT 封裝 / 箱體:SOIC-8 |
| FM24C256EM8X | 制造商:未知廠家 制造商全稱:未知廠家 功能描述:I2C Serial EEPROM |
發布緊急采購，3分鐘左右您將得到回復。