- 您現在的位置：買賣IC網 > PDF目錄375726 > FAN7040 (Fairchild Semiconductor Corporation) 3W Mono BTL Amplifier with DC Volume Control PDF資料下載
參數資料
| 型號： | FAN7040 |
| 廠商： | Fairchild Semiconductor Corporation |
| 英文描述： | 3W Mono BTL Amplifier with DC Volume Control |
| 中文描述： | 3W單聲道BTL放大器直流音量控制 |
| 文件頁數： | 9/12頁 |
| 文件大?。?/td> | 241K |
| 代理商： | FAN7040 |
FAN7040
9
Typical Application Information
Functional Description
The FAN7040 is a mono BTL output amplifier with DC volume control. It is designed for use in TVs and monitors but is also
suitable for battery-fed portable recorders and radios.
In conventional DC volume circuits the control or input stage is AC-coupled to the output stage via external capacitors to keep
the offset voltage low. In the FAN7040 the DC volume control stage is integrated into the input stage so that no coupling
capacitors are required. With this configuration, a low offset voltage is still maintained and the minimum supply voltage
remains low.
The BTL principle offers the following advantages:
Lower peak value of the supply current
The frequency of the ripple on the supply voltage is twice the signal frequency.
Consequently, a reduced power supply with smaller capacitors can be used which also results in cost reductions. For portable
applications there is a trend to decrease the supply voltage, resulting in a reduction of output power at conventional output
stages. Using the BTL principle increases the output power. The maximum gain of the amplifier is fixed at 37dB. The DC vol-
ume control stage has a logarithmic control characteristic. The total gain can be controlled from 37dB to -52dB. If the DC vol-
ume control voltage is below 0.3V, the device switches to the mute mode. The amplifier is short-circuit proof to ground, Vcc
and across the load. A thermal protection circuit is also implemented. If the crystal temperature rises above +150°C the TSD is
operated, thereby the output power is off. Special attention is given to switch-on and switch-off clicks, low HF radiation and a
good overall stability.
Voltage Gain
The maximum closed-loop voltage gain has been internally fixed at 37dB.
Output Power
The output power as a function of supply voltage has been measured at THD=10%. The maximum output power is limited by
the maximum allowed power dissipation at Ta=25°C approximately 1.8W, and the maximum available output current is 1.25A
repetitive peak current.
Short Circuit Protection
The output (pins 14 and 17) can be short-circuited to ground respectively to +VDD. The Missing Current Limiter(MCL) pro-
tection circuit will shut-off the amplifier. Removing the short-circuit will reset the amplifier automatically. Short-circuit across
the load(pins 14 and 17) will activate the thermal protection circuit; this will result in thermal shutdown protection.
For single-end application the output peak current may not exceed 130mA; at higher output currents the short circuit protec-
tion(MCL) will be activated.
Power Dissipation
Power dissipation is a major concern when designing any power amplifier and must be thoroughly understood to ensure a suc-
cessful design. Equation (1) states the maximum power dissipation point for a bridged amplifier operating at a given supply
voltage and driving a specified output load.
2
----------------
=
(1)
Since the FAN7040 is driving a bridged amplifier, the internal maximum power dissipation point of the FAN7040 results from
equation (1). Even with the large internal power dissipation, the FAN7040 does not require heat sinking over a wide range of
ambient temperature. From equation (1), assuming a 12V power supply and a 16
load, the maximum power dissipation point
is 1.8W. The maximum power dissipation point obtained from equation (1) must not be greater than the power dissipation that
results from equation (2) :
For package 20SOP, R
thja
=70°C/W, T
JMAX
=150°C for the FAN7040.
P
DMAX
4
V
2
π
2
R
L
P
DMAX
T
---------------------------------
T
–
(
)
R
thja
=
(2)
相關PDF資料 |
PDF描述 |
|---|---|
| FAN7040M | 3W Mono BTL Amplifier with DC Volume Control |
| FAN7040MX | 3W Mono BTL Amplifier with DC Volume Control |
| FAN7071 | Landing Correction IC |
| FAN7300 | LCD Back Light Inverter Drive IC |
| FAN7300G | LCD Back Light Inverter Drive IC |
相關代理商/技術參數 |
參數描述 |
|---|---|
| FAN7040M | 功能描述:音頻放大器 3W MONO POWER AMP RoHS:否 制造商:STMicroelectronics 產品:General Purpose Audio Amplifiers 輸出類型:Digital 輸出功率: THD + 噪聲: 工作電源電壓:3.3 V 電源電流: 最大功率耗散: 最大工作溫度: 安裝風格:SMD/SMT 封裝 / 箱體:TQFP-64 封裝:Reel |
| FAN7040MX | 功能描述:音頻放大器 3W MONO POWER AMP RoHS:否 制造商:STMicroelectronics 產品:General Purpose Audio Amplifiers 輸出類型:Digital 輸出功率: THD + 噪聲: 工作電源電壓:3.3 V 電源電流: 最大功率耗散: 最大工作溫度: 安裝風格:SMD/SMT 封裝 / 箱體:TQFP-64 封裝:Reel |
| FAN7071 | 制造商:FAIRCHILD 制造商全稱:Fairchild Semiconductor 功能描述:Landing Correction IC |
| FAN7071S | 功能描述:特殊用途放大器 RoHS:否 制造商:Texas Instruments 通道數量:Single 共模抑制比（最小值）: 輸入補償電壓: 工作電源電壓:3 V to 5.5 V 電源電流:5 mA 最大功率耗散: 最大工作溫度:+ 70 C 最小工作溫度:- 40 C 安裝風格:SMD/SMT 封裝 / 箱體:QFN-20 封裝:Reel |
| FAN7071TS | 功能描述:功率因數校正 IC Land Correction IC RoHS:否 制造商:Fairchild Semiconductor 開關頻率:300 KHz 最大功率耗散: 最大工作溫度:+ 125 C 安裝風格:SMD/SMT 封裝 / 箱體:SOIC-8 封裝:Reel |
發布緊急采購，3分鐘左右您將得到回復。