- 您現在的位置：買賣IC網 > PDF目錄375725 > FAN5608MPX (FAIRCHILD SEMICONDUCTOR CORP) Serial/Parallel LED Driver with Current-Regulated, Step-Up DC/DC Converter PDF資料下載
參數資料
| 型號： | FAN5608MPX |
| 廠商： | FAIRCHILD SEMICONDUCTOR CORP |
| 元件分類： | 顯示驅動器 |
| 英文描述： | Serial/Parallel LED Driver with Current-Regulated, Step-Up DC/DC Converter |
| 中文描述： | LED DISPLAY DRIVER, DSO8 |
| 封裝： | 3 X 3 MM, MO-229VEEC, MLP-8 |
| 文件頁數： | 6/17頁 |
| 文件大?。?/td> | 206K |
| 代理商： | FAN5608MPX |
PRODUCT SPECIFICATION
FAN5608
6
REV. 1.0.3 6/28/04
Digital Control
The FAN5608’s digital decoder allows selection of the fol-
lowing modes of operation: OFF, 5mA, 10mA, 20mA per
branch.
Analog Control
Inputs A1 and A2 are used to control the LED currents.
Inputs B1 and B2 should be connected to GND (logic level
“0”). An external resistor (R) is connected from A1 and/or
A2 to a stable voltage source (V
current, I
LED
. The I
LED
can be determined using the formula
and the graph below:
External
) to control the LED
Where V
Ref
= 1.22V, V
Ref
< V
External
< (V
IN
– 0.7V)
PWM Control in Digital Mode
The logic level HIGH, VH and logic level LOW, VL of the
PWM signal should be:
(V
IN
– 0.7V) < VH < V
IN
and 0 < VL < 0.6V
The frequency of the PWM signal should be within 50Hz to
1kHz range; it can go up to 30kHz at any input if the other
input is kept HIGH. In the case of FAN5608MPX and
FAN5608DMPX, the B1 and B2 inputs are internally con-
nected to GND and the PWM signal can be applied to A1
and A2 inputs only. Consequently, the maximum LED
current, for 100% duty cycle, is 5mA on each channel.
PWM Control in Analog Mode
The logic level HIGH, VH and logic level LOW, VL of the
PWM signal should be:
V
Ref
< VH < (V
IN
– 0.7V) and 0 < VL < 0.6V
The frequency of the PWM signal should be within 50Hz
to 1kHz range. The VH sets the maximum LED current
while the duty cycle sets the average current between 0 and
I
LEDmax
.
If the analog inputs A1 and/or A2 are driven in digital mode
by an open drain output, it is important to choose the appro-
priate value of the pull-up resistor. Its resistance should be
low enough to ensure less than 0.7V dropout, hence V
A
>
(V
IN
– 0.7V) as required for HIGH logic level:
Open-Circuit Protection
A built-in over voltage protection circuit prevents the device
from being damaged when it is powered up with no load.
This circuit reduces the boost converter duty cycle, to a
minimum thus limiting the output voltage to a safe value
when no load condition is detected. If one of the two enable
branches is accidentally disconnected, the converter contin-
ues the operation, however, the current in the remaining
branch is no longer regulated and the actual branch current
will be determined by the input voltage, the inductor value
and the switching frequency.
However, the FAN5608 can be damaged when a full load
(more than six LEDs, driven by 20mA) is suddenly discon-
nected from V
OUT
. To protect the FAN5608 against this
unlikely event, an external 24V Zener diode can be con-
nected between V
OUT
and GND.
Shutdown Mode
Each branch can be independently disabled by applying
LOW logic level voltage to the A and B inputs. When both
branches are disabled, the FAN5608 enters Shutdown mode
and the supply current is reduced to less than 1
μ
A.
A
B
0
0
1
0
0
1
1
1
I
LED
OFF
5mA
10mA
20mA
I
LED
V
-----------------R
V
–
Multiplication Ratio
×
=
0
1.25
5
10
15
20
25
1.5
1.75
2
2.25
2.5
2.75
3
3.25
3.5
V
External
(V)
I
L
(
R=10Kohm
R=100kohm
R
pull
up
–
μ
A
60
<
11.66k
=
相關PDF資料 |
PDF描述 |
|---|---|
| FAN5608 | Serial/Parallel LED Driver with Current-Regulated, Step-Up DC/DC Converter |
| FAN5608DHMPX | Serial/Parallel LED Driver with Current-Regulated, Step-Up DC/DC Converter |
| FAN5608HMPX | Serial/Parallel LED Driver with Current-Regulated, Step-Up DC/DC Converter |
| FAN5609 | LED Driver with Adaptive Charge Pump DC/DC Converter |
| FAN5609MPX | TERMINAL |
相關代理商/技術參數 |
參數描述 |
|---|---|
| FAN5608MPX_Q | 功能描述:LED照明驅動器 LED Driver Serial/Parallel RoHS:否 制造商:STMicroelectronics 輸入電壓:11.5 V to 23 V 工作頻率: 最大電源電流:1.7 mA 輸出電流: 最大工作溫度: 安裝風格:SMD/SMT 封裝 / 箱體:SO-16N |
| FAN5609 | 制造商:FAIRCHILD 制造商全稱:Fairchild Semiconductor 功能描述:LED Driver with Adaptive Charge Pump DC/DC Converter |
| FAN5609_AFC3086B WAF | 制造商:Fairchild Semiconductor Corporation 功能描述: |
| FAN5609_AGC3026B WAF | 制造商:Fairchild Semiconductor Corporation 功能描述: |
| FAN5609MPX | 功能描述:LED照明驅動器 LED Driver DC/DC Converter RoHS:否 制造商:STMicroelectronics 輸入電壓:11.5 V to 23 V 工作頻率: 最大電源電流:1.7 mA 輸出電流: 最大工作溫度: 安裝風格:SMD/SMT 封裝 / 箱體:SO-16N |
發布緊急采購，3分鐘左右您將得到回復。