參數資料
型號: FA5331M
廠商: FUJI ELECTRIC CO LTD
元件分類: 穩壓器
英文描述: Bipolar IC For Power Factor Correction
中文描述: 1.5 A POWER FACTOR CONTROLLER, 220 kHz SWITCHING FREQ-MAX, PDSO16
封裝: PLASTIC, SOP-16
文件頁數: 6/13頁
文件大?。?/td> 151K
代理商: FA5331M
6
FA5331P(M)/FA5332P(M)
3. Current error amplifier and overcurrent limiting circuit
The current error amplifier forms a current loop to change the
input circuit current into sinusoidal waves. As Fig. 3 shows, the
multiplier output is connected to pin 2 (IIN –) through a resistor
(RA) to input the reference current signal. Pin 16 (IDET) is a
current input terminal. Design the circuit so that the voltage at
pin 16 will be within the range from 0 (GND potential) to –1.0V.
Connect a phase correction resistor and capacitors across pin
1 (amplifier output) and pin 2. See Fig. 4 for the expected gain
characteristics of the circuit shown in Fig. 3.
Here,
1
2
π
R5 C3
Z =
..................................................(5)
p =
1
2
π
R5 C
.............................................(6)
C =
C2 C3
C2 + C3
The voltage gain (G1) between Z and P of the circuit (gain
between pins 16 and 1) is given as follows:
G1 = 20 log
10
{ 0.75 (
R5
RA
+ 1) }
....................(7)
Ensure an adequate phase margin by selecting C1 and C2 so
that the p/z ratio is about 10. The current error amplifier output
is used as an input to the comparator for PWM.
The overcurrent detection comparator (C2) limits an
overcurrent. The threshold voltage for overcurrent detection at
pin 16 is –1.15V for FA5331 and –1.10V for FA5332. Connect
noise filters Rn and Cn to prevent the voltage at pin 16 from
fluctuating due to noise, causing the comparator to malfunction.
For Rn, select a resistor of up to 100
for FA5331 and up to
27
for FA5332. (See P64, 4. No-load operation )
4. Comparator for PWM
Figure 5 shows the comparator for PWM. When the oscillator
output (Va) is smaller than the current error amplifier output
(Vc), the comparator output is high and the output ON signal is
generated at pin 8. Pin 11 (CS) is a terminal for soft start. This
terminal charges capacitor C4 with the internal constant current
(10
μ
A) for a soft start. Priority is given to Vb and Vc whichever
is lower.
5. Multiplier
The multiplier generates a reference current signal. Input a
fully rectified sinusoidal signal voltage into pin 3 (VDET).
Design the circuit to keep the peak voltage at pin 3 within a
range from 0.65V to 2V for FA5331 and 0.65V to 2.4V for
FA5332. The multiplier output voltage (Vm) is roughly given as
follows (see Fig. 6):
Vm = 1.25 – (Ve –1.55) Vs.................................... (8)
As Fig. 3 shows Vm is internally connected to pin 2 (IIN–) of the
current error amplifier A2 through a 10k
resistor. (See the
characteristic curve, page 66 for the input and output
characteristics of the multiplier.)
Fig. 6 Multiplier
Fig. 4 Voltage gain-frequency
Fig. 3 Current error amplifier and overcurrent limiting circuit
Fig. 5 PWM comparator
PWM
VREF
_
+
A2
F.F
Vocp
2
1
46
Rn
Cn
RC
5k
RB
15k
5V
C2
C3
C2
Vm
RA
10k
R5
comparator
Current
detection
MUL
CURR.AMP
OPC
G1
(dB)
Voltage gain
Z
P
Frequency
R7
Ve
ER.AMP(A1) output
Vs
Vm
V
IN
R6
3
MUL
C4
Vb
10
μ
A
CS
C3
Oscillator output Va
PWM comparator
CURR.AMP(A2) output Vc
11
相關PDF資料
PDF描述
FA5332M Bipolar IC For Power Factor Correction
FA5332P Bipolar IC For Power Factor Correction
FA5332PM Bipolar IC For Power Factor Correction
FA5502 POWER SUPPLY CONTROL IC
FA5530 Quasi-Resonant IC
相關代理商/技術參數
參數描述
FA5331P 制造商:Panasonic Industrial Company 功能描述:IC
FA5331P(M) 制造商:未知廠家 制造商全稱:未知廠家 功能描述:FA5331P(M) and FA5332P(M) are control ICs for a power factor correction system.
FA5331PM 制造商:FUJI 制造商全稱:Fuji Electric 功能描述:Bipolar IC For Power Factor Correction
FA5332M 制造商:FUJI 制造商全稱:Fuji Electric 功能描述:Bipolar IC For Power Factor Correction
FA5332P 制造商:FUJI 制造商全稱:Fuji Electric 功能描述:Bipolar IC For Power Factor Correction