- 您現在的位置：買賣IC網 > PDF目錄375715 > FA531X (FUJI ELECTRIC HOLDINGS CO., LTD.) Bipolar IC For Switching Power Supply Control PDF資料下載
參數資料
| 型號： | FA531X |
| 廠商： | FUJI ELECTRIC HOLDINGS CO., LTD. |
| 元件分類： | 基準電壓源/電流源 |
| 英文描述： | Bipolar IC For Switching Power Supply Control |
| 中文描述： | 雙極集成電路開關電源控制 |
| 文件頁數： | 9/17頁 |
| 文件大?。?/td> | 263K |
| 代理商： | FA531X |
9
FA531X series
I
Design advice
1. Startup circuit
It is necessary to start-up IC that the voltage inclination of
VCC terminal “dVcc/dt” satisfies the following equation(4).
dVcc/dt(V/s)>1.8/Cs(
μ
F)...............................(4)
Cs : Capacitor connected between CS terminal and GND
Note that equation (4) must be satisfied in any condition. Also,
it is necessary to keep “l(fā)atch mode” for overload protection or
overvoltage protection that the current supplied to VCC
terminal through startup resistor satisfies the following
equation(5).
Icc(Lat)> 0.4mA for Vcc
%
9.2V ..................(5)
Icc(Lat) : Cutoff-state( = Latch mode ) supply current
The detail is explained as follows.
(1) Startup circuit connected to AC line directly
Fig. 20 shows a typical startup circuit that a startup
resistor Rc is connected to AC line directly. The period from
power-on to startup is determined by Rc, R
D
and C
A
. Rc, R
D
and C
A
must be designed to satisfy the following equations.
dVcc/dt(V/s)=
(1/C
A
) {(V
AVE
–Vccon )/R
C
–Vccon/R
D
–Iccst} >
1.8/(Cs(
μ
F))................................................(6)
Rc(k
)< (V
AVE
–9.2(V))/{0.4 (mA) + (9.2(V)/R
D
(k
) } ...........(7)
V
AVE
= Vac
E
2/
π
:
Average voltage applied to AC line side of Rc
Vac:
AC input effective voltage
Vccon: ON threshold of UVLO, 16.5V(max.) or 16.2V(max.)
Iccst:
Standby current, 0.15 mA(max.)
In this method, Vcc voltage includes ripple voltage influenced
by AC voltage. Therefore, enough dVcc/dt required by
equation (6) tend to be achieved easily when Vcc reaches to
Vccon even if Vcc goes up very slowly. After power-off, Vcc
does not rise up because a voltage applied from bias winding
to VCC terminal decreases and the current flowing R
C
be-
comes zero, therefore, re-startup does not occur after Vcc falls
down below OFF threshold of UVLO until next power-on.
Fig. 20 Startup circuit example(1)
相關PDF資料 |
PDF描述 |
|---|---|
| FA5331P | Bipolar IC For Power Factor Correction |
| FA5331PM | Bipolar IC For Power Factor Correction |
| FA5331M | Bipolar IC For Power Factor Correction |
| FA5332M | Bipolar IC For Power Factor Correction |
| FA5332P | Bipolar IC For Power Factor Correction |
相關代理商/技術參數 |
參數描述 |
|---|---|
| FA5321P | 制造商:未知廠家 制造商全稱:未知廠家 功能描述: |
| FA5331M | 制造商:FUJI 制造商全稱:Fuji Electric 功能描述:Bipolar IC For Power Factor Correction |
| FA5331P | 制造商:Panasonic Industrial Company 功能描述:IC |
| FA5331P(M) | 制造商:未知廠家 制造商全稱:未知廠家 功能描述:FA5331P(M) and FA5332P(M) are control ICs for a power factor correction system. |
| FA5331PM | 制造商:FUJI 制造商全稱:Fuji Electric 功能描述:Bipolar IC For Power Factor Correction |
發布緊急采購，3分鐘左右您將得到回復。