- 您現在的位置：買賣IC網 > PDF目錄382952 > F2M03GLA (Electronic Theatre Controls, Inc.) Low power Bluetooth⑩ Module with antenna PDF資料下載
參數資料
| 型號： | F2M03GLA |
| 廠商： | Electronic Theatre Controls, Inc. |
| 英文描述： | Low power Bluetooth⑩ Module with antenna |
| 中文描述： | ⑩低功耗藍牙模塊天線 |
| 文件頁數： | 12/44頁 |
| 文件大?。?/td> | 669K |
| 代理商： | F2M03GLA |
第1頁第2頁第3頁第4頁第5頁第6頁第7頁第8頁第9頁第10頁第11頁當前第12頁第13頁第14頁第15頁第16頁第17頁第18頁第19頁第20頁第21頁第22頁第23頁第24頁第25頁第26頁第27頁第28頁第29頁第30頁第31頁第32頁第33頁第34頁第35頁第36頁第37頁第38頁第39頁第40頁第41頁第42頁第43頁第44頁
Rev: b
Low power Bluetooth
Module with antenna- F2M03GLA
Datasheet
5.1.2 Settings
The default settings allow the user to communicate via Bluetooth, without sending any configuration
commands, as soon as a successful connection has been established. Information sent and received on
the serial interface of the WU unit at 38400 bps is transmitted transparently between the two connected
devices. The default settings are valid as long as the user has made no configuration.
When there is no Bluetooth connection established it is possible to configure the WU firmware via
commands sent on the serial interface. All settings changed by the user are stored in persistent memory.
The following serial settings are used for configuration mode and are not configurable:
Parameter
Default Value
Baud rate
38400
Data bits
8
Parity
None
Stop bits
1
Hardware flow control
On
To be able to send commands to the Wireless UART firmware, it must be set in
Host Controlled Mode
(HCM). As previously described the Wireless UART firmware can only enter HCM when no Bluetooth
connection is established.
Once entered HCM there are several commands that can be issued:
Configuration commands
Software / Hardware reboot
Inquiry (search for Bluetooth devices in the neighborhood)
Pairing (device security - authentication and encryption)
Advanced configuration commands
SCO commands
Information commands
Control commands
Configuration Commands
There are several settings stored in the Wireless UART firmware that can be read and modified by using
the configuration commands.
Examples of these settings are:
Local Bluetooth name
Local SDP-service name
Operating mode
Serial port settings
Bluetooth security settings (authentication, encryption)
There are two normal operating modes:
Connecting mode – Bluetooth master
Endpoint mode – Bluetooth slave
In Connecting mode the Wireless UART firmware will continuously try to establish a Bluetooth connection to
a specified remote Bluetooth device in the neighborhood (Bluetooth master).
connection request will be accepted when the specified rules are fulfilled (Bluetooth slave).
2006 Free2move AB
Page 12(44)
相關PDF資料 |
PDF描述 |
|---|---|
| F2M03GLA-S01 | Low power Bluetooth⑩ Module with antenna |
| F2M03GLA-S04 | Low power Bluetooth⑩ Module with antenna |
| F308 | Previous Vectron Model Numbers |
| F607 | ULTRAHIGH - SPEED SWITCHING, MOTOR DRIVER APPLICATIONS |
| F82C206 | NEW ENHANCED AT DATA BOOK |
相關代理商/技術參數 |
參數描述 |
|---|---|
| F2M03GLA-S01 | 制造商:Free2move 功能描述:MOD BLUETOOTH V2.0+EDR SPP W/ANT |
| F2M03GLA-S04 | 制造商:Free2move 功能描述:MOD BLUETOOTH V2.0+EDR USB W/ANT |
| F2M03GXA-S01 | 制造商:Free2move 功能描述:MOD BLUETOOTH V2.0+EDR EXT W/ANT |
| F2M03GXA-S01-R2A | 制造商:Free2move 功能描述:MOD BLUETOOTH V2.0+EDR EXT W/ANT |
| F2M03GXA-S04 | 制造商:Free2move 功能描述:MOD BLUETOOTH V2.0+EDR EXT W/ANT |
發布緊急采購，3分鐘左右您將得到回復。