- 您現在的位置：買賣IC網 > PDF目錄382952 > F2M03GLA-S04 (Electronic Theatre Controls, Inc.) Low power Bluetooth⑩ Module with antenna PDF資料下載
參數資料
| 型號： | F2M03GLA-S04 |
| 廠商： | Electronic Theatre Controls, Inc. |
| 英文描述： | Low power Bluetooth⑩ Module with antenna |
| 中文描述： | ⑩低功耗藍牙模塊天線 |
| 文件頁數： | 20/44頁 |
| 文件大?。?/td> | 669K |
| 代理商： | F2M03GLA-S04 |
第1頁第2頁第3頁第4頁第5頁第6頁第7頁第8頁第9頁第10頁第11頁第12頁第13頁第14頁第15頁第16頁第17頁第18頁第19頁當前第20頁第21頁第22頁第23頁第24頁第25頁第26頁第27頁第28頁第29頁第30頁第31頁第32頁第33頁第34頁第35頁第36頁第37頁第38頁第39頁第40頁第41頁第42頁第43頁第44頁
Rev: b
Low power Bluetooth
Module with antenna- F2M03GLA
Datasheet
6.2 USB Interface
F2M03 contain a full-speed (12Mbits/s) USB interface, capable of driving a USB cable directly. No external
USB transceiver is required. The device operates as a USB peripheral, responding to requests from a
master host controller such as a PC. Both the OHCI and the UHCI standards are supported. The set of
USB endpoints implemented behave as specified in the USB section of the Bluetooth specification
v2.0+EDR. As USB is a master-slave orientated system, F2M03 only supports USB slave operation.
Note:
The USB interface can only be used with the HCI firmware
6.2.1 USB Data Connections
The USB data lines emerge as pins USB_DP (USB +) and USB_DN (USB -) on the package. These
terminals are connected to the internal USB I/O buffers of F2M03 and therefore have low output
impedance. To match the connection to the characteristic impedance of the USB cable, series resistors
must be connected to both USB + and USB -.
6.2.2 USB Pull-up Resistor
F2M03 features an internal USB pull-up resistor. This pulls the USB_DP pin weakly high when F2M03 is
ready to enumerate. It signals to the PC that it is a full-speed (12Mbit/s) USB device.
The USB internal pull-up is implemented as a current source, and is compliant with 7.1.5 of the USB
specification v1.1. The internal pull-up pulls USB DP high to at least 2.8V when loaded with a 15k
-5%
pull-down resistor (in the hub/host) (when VDD=3.1V). This presents a the venin resistance to the host of at
least 900
. Alternatively, an external 1.5k
pull-up resistor can be placed between a PIO line and D+ on
the USB cable. The firmware must be alerted to which mode is used (contact Free2move). The default
setting uses the internal pull-up resistor.
6.2.3 Power Supply
The minimum output high voltage for USB data lines is 2.8V. To safely meet the USB specification, the
voltage on terminals must be an absolute minimum of 3.1V. Free2move recommends 3.3V for optimal USB
signal quality.
6.2.4 Self-Powered Mode
In self-powered mode, the circuit is powered from its own power supply and not from the VBUS (5V) line of
the USB cable. It draws only a small leakage current (below 0.5mA) from VBUS on the USB cable. This is
the easier mode for which to design for, as the design is not limited by the power that can be drawn from
the USB hub or root port. However, it requires that VBUS be connected to F2M03 via a resistor network
(Rvb1 and Rvb2), so F2M03 can detect when VBUS is powered up. F2M03 will not pull USB + high when
VBUS is off.
PIO
USB +
USB –
USB ON
Connections to F2M03 for Self-Powered Mode
The terminal marked USB ON can be any free PIO pin. The PIO pin selected must be registered by settings in firmware (contact
Free2move) to the corresponding pin number
2006 Free2move AB
Page 20(44)
相關PDF資料 |
PDF描述 |
|---|---|
| F308 | Previous Vectron Model Numbers |
| F607 | ULTRAHIGH - SPEED SWITCHING, MOTOR DRIVER APPLICATIONS |
| F82C206 | NEW ENHANCED AT DATA BOOK |
| F82C211 | NEW ENHANCED AT DATA BOOK |
| F82C212 | NEW ENHANCED AT DATA BOOK |
相關代理商/技術參數 |
參數描述 |
|---|---|
| F2M03GXA-S01 | 制造商:Free2move 功能描述:MOD BLUETOOTH V2.0+EDR EXT W/ANT |
| F2M03GXA-S01-R2A | 制造商:Free2move 功能描述:MOD BLUETOOTH V2.0+EDR EXT W/ANT |
| F2M03GXA-S04 | 制造商:Free2move 功能描述:MOD BLUETOOTH V2.0+EDR EXT W/ANT |
| F2M03GX-S01 | 制造商:Free2move 功能描述:MOD BLUETOOTH V2.0+EDR SPP EXT. |
| F2M03GX-S04 | 制造商:Free2move 功能描述:MOD BLUETOOTH V2.0+EDR USB EXT. |
發布緊急采購，3分鐘左右您將得到回復。