- 您現在的位置：買賣IC網 > PDF目錄17026 > EVAL-AD977CB (Analog Devices Inc)BOARD EVAL FOR AD977 PDF資料下載
參數資料
| 型號： | EVAL-AD977CB |
| 廠商： | Analog Devices Inc |
| 文件頁數： | 10/24頁 |
| 文件大?。?/td> | 0K |
| 描述： | BOARD EVAL FOR AD977 |
| 標準包裝： | 1 |
| ADC 的數量： | 1 |
| 位數： | 16 |
| 采樣率（每秒）： | 100k |
| 數據接口： | 串行 |
| 輸入范圍： | ±10 V |
| 在以下條件下的電源（標準）： | 100mW @ 100kSPS |
| 工作溫度： | -40°C ~ 85°C |
| 已用 IC / 零件： | AD977 |
| 已供物品： | 板 |
| 相關產品： | AD977CRSZ-ND - IC ADC 16BIT SRL 100KSPS 28SSOP AD977BRZ-ND - IC ADC 16BIT 100KSPS 20SOIC AD977BRSZ-ND - IC ADC 16BIT 100KSPS 28SSOP AD977BNZ-ND - IC ADC 16BIT 100KSPS 20DIP AD977ARSZ-ND - IC ADC 16BIT 100KSPS 28SSOP AD977ACRZ-ND - IC ADC 16BIT 200KSPS 20SOIC AD977ACRSZ-ND - IC ADC 16BIT 200KSPS 28SSOP AD977ABNZ-ND - IC ADC 16BIT 200KSPS 20DIP AD977ACNZ-ND - IC ADC 16BIT 200KSPS 20DIP AD977AANZ-ND - IC ADC 16BIT 200KSPS 20DIP 更多... |
AD977/AD977A
–18–
REV. D
VOLTAGE REFERENCE
The AD977/AD977A has an on-chip temperature compensated
bandgap voltage reference that is factory trimmed to 2.5 V
±20 mV. The accuracy of the AD977/AD977A over the speci-
fied temperature ranges is dominated by the drift performance
of the voltage reference. The on-chip voltage reference is laser-
trimmed to provide a typical drift of 7 ppm/
°C. This typical drift
characteristic is shown in Figure 14, which is a plot of the
change in reference voltage (in mV) versus the change in tem-
perature—notice the plot is normalized for zero error at 25
°C.
If improved drift performance is required, an external reference
such as the AD780 should be used to provide a drift as low as
3 ppm/
°C. In order to simplify the drive requirements of the
voltage reference (internal or external), an onboard reference
buffer is provided. The output of this buffer is provided at the
CAP pin and is available to the user; however, when externally
loading the reference buffer, it is important to make sure that
proper precautions are taken to minimize any degradation in the
ADC’s performance. Figure 15 shows the load regulation of the
reference buffer. Notice that this figure is also normalized so
that there is zero error with no dc load. In the linear region, the
output impedance at this point is typically 1
. Because of this
1
output impedance, it is important to minimize any ac or
DEGREES CELSIUS
–55
1mV/DIV
25
125
Figure 14. Reference Drift
LOAD CURRENT – 5mA/DIV
dV
ON
CAP
PIN
–
10mV/DIV
SOURCE CAPABILITY
SINK CAPABILITY
Figure 15. CAP Pin Load Regulation
input dependent loads that will lead to increased distortion.
Any dc loads will simply act as a gain error. Although the typi-
cal characteristic of Figure 15 shows that the AD977/AD977A
is capable of driving loads greater than 15 mA, it is recom-
mended that the steady state current not exceed 2 mA.
Using an External Reference
In addition to the on-chip reference, an external 2.5 V refer-
ence can be applied. When choosing an external reference for a
16-bit application, however, careful attention should be paid to
noise and temperature drift. These critical specifications can
have a significant effect on the ADC performance.
Figures 16a and 16b show the AD977/AD977A used in bipolar
mode with the AD780 voltage reference applied to the REF
pin. It is important to note that in Figure 16a the R3IN pin is
connected to the CAP pin whereas in Figure 16b the R3IN pin
of the AD977A is returned to the output of the external refer-
ence. The AD780 is a bandgap reference that exhibits ultralow
drift, low initial error and low output noise. In Figure 16b,
the value for C1 is only applicable to applications using the
AD780. In applications using a different external reference a
different value for C1 may be required. For low power applica-
tions, the REF192 provides a low quiescent current, high
accuracy and low temperature drift solution.
200
VIN
33.2k
C2
2.2 F
R1IN
R2IN
R3IN
REF
AGND2
CAP
AGND1
AD977
VANA
C4
0.1 F
C1
2.2 F
C3
1 F
4
GND
6
VOUT
VIN
TEMP
AD780
3
2
0.1 F
5V
100
Figure 16a. AD780 External Reference to AD977 Config-
ured for
±10 V Input Range
200
VIN
33.2k
C2
2.2 F
R1IN
R2IN
R3IN
REF
AGND2
CAP
AGND1
AD977A
VANA
C4
0.1 F
C1
330 F*
C3
1 F
4
GND
6
VOUT
VIN
TEMP
AD780
3
2
0.1 F
5V
100
*ESR AT 100kHz MUST BE LESS THAN 0.3 .
RECOMMEND KEMET T495 SERIES OR
SANYO 6SA330M.
Figure 16b. AD780 External Reference to AD977A Config-
ured for
±10 V Input Range
相關PDF資料 |
PDF描述 |
|---|---|
| CDB5529 | EVAL BOARD FOR CS5529 |
| VE-J1F-EY | CONVERTER MOD DC/DC 72V 50W |
| GCM22DSXH | CONN EDGECARD 44POS DIP .156 SLD |
| CDB5368 | BOARD EVAL FOR CS5368 192KHZ ADC |
| VE-J1B-EY | CONVERTER MOD DC/DC 95V 50W |
相關代理商/技術參數 |
參數描述 |
|---|---|
| EVAL-AD9830EBZ | 功能描述:BOARD EVALUATION AD9830 RoHS:是 類別:編程器，開發系統 >> 評估演示板和套件 系列:- 標準包裝:1 系列:- 主要目的:電信，線路接口單元（LIU） 嵌入式:- 已用 IC / 零件:IDT82V2081 主要屬性:T1/J1/E1 LIU 次要屬性:- 已供物品:板，電源，線纜，CD 其它名稱:82EBV2081 |
| EVAL-AD9831EB | 制造商:Analog Devices 功能描述: |
| EVAL-AD9831EBZ | 功能描述:BOARD EVALUATION AD9831 RoHS:是 類別:編程器，開發系統 >> 評估演示板和套件 系列:- 標準包裝:1 系列:- 主要目的:電信，線路接口單元（LIU） 嵌入式:- 已用 IC / 零件:IDT82V2081 主要屬性:T1/J1/E1 LIU 次要屬性:- 已供物品:板，電源，線纜，CD 其它名稱:82EBV2081 |
| EVAL-AD9832EB | 制造商:Analog Devices 功能描述:EVALUATION BOARD I.C. - Bulk 制造商:Analog Devices 功能描述:AD9832 EVAL BOARD |
| EVAL-AD9832SDZ | 功能描述:BOARD EVAL FOR AD9832 RoHS:是 類別:編程器，開發系統 >> 評估演示板和套件 系列:* 標準包裝:1 系列:- 主要目的:電信，線路接口單元（LIU） 嵌入式:- 已用 IC / 零件:IDT82V2081 主要屬性:T1/J1/E1 LIU 次要屬性:- 已供物品:板，電源，線纜，CD 其它名稱:82EBV2081 |
發布緊急采購，3分鐘左右您將得到回復。